flipperzero-firmware/firmware/targets/f6/furi-hal/furi-hal-spi-config.c

#include <furi-hal-spi-config.h>
#include <furi-hal-resources.h>

extern SPI_HandleTypeDef SPI_R;
extern SPI_HandleTypeDef SPI_D;

const SPI_InitTypeDef furi_hal_spi_config_nfc = {
    .Mode = SPI_MODE_MASTER,
    .Direction = SPI_DIRECTION_2LINES,
    .DataSize = SPI_DATASIZE_8BIT,
    .CLKPolarity = SPI_POLARITY_LOW,
    .CLKPhase = SPI_PHASE_2EDGE,
    .NSS = SPI_NSS_SOFT,
    .BaudRatePrescaler = SPI_BAUDRATEPRESCALER_8,
    .FirstBit = SPI_FIRSTBIT_MSB,
    .TIMode = SPI_TIMODE_DISABLE,
    .CRCCalculation = SPI_CRCCALCULATION_DISABLE,
    .CRCPolynomial = 7,
    .CRCLength = SPI_CRC_LENGTH_DATASIZE,
    .NSSPMode = SPI_NSS_PULSE_DISABLE,
};

const SPI_InitTypeDef furi_hal_spi_config_subghz = {
    .Mode = SPI_MODE_MASTER,
    .Direction = SPI_DIRECTION_2LINES,
    .DataSize = SPI_DATASIZE_8BIT,
    .CLKPolarity = SPI_POLARITY_LOW,
    .CLKPhase = SPI_PHASE_1EDGE,
    .NSS = SPI_NSS_SOFT,
    .BaudRatePrescaler = SPI_BAUDRATEPRESCALER_8,
    .FirstBit = SPI_FIRSTBIT_MSB,
    .TIMode = SPI_TIMODE_DISABLE,
    .CRCCalculation = SPI_CRCCALCULATION_DISABLE,
    .CRCPolynomial = 7,
    .CRCLength = SPI_CRC_LENGTH_DATASIZE,
    .NSSPMode = SPI_NSS_PULSE_DISABLE,
};

const SPI_InitTypeDef furi_hal_spi_config_display = {
    .Mode = SPI_MODE_MASTER,
    .Direction = SPI_DIRECTION_2LINES,
    .DataSize = SPI_DATASIZE_8BIT,
    .CLKPolarity = SPI_POLARITY_LOW,
    .CLKPhase = SPI_PHASE_1EDGE,
    .NSS = SPI_NSS_SOFT,
    .BaudRatePrescaler = SPI_BAUDRATEPRESCALER_16,
    .FirstBit = SPI_FIRSTBIT_MSB,
    .TIMode = SPI_TIMODE_DISABLE,
    .CRCCalculation = SPI_CRCCALCULATION_DISABLE,
    .CRCPolynomial = 7,
    .CRCLength = SPI_CRC_LENGTH_DATASIZE,
    .NSSPMode = SPI_NSS_PULSE_ENABLE,
};

/**
 * SD Card in fast mode (after init)
 */
const SPI_InitTypeDef furi_hal_spi_config_sd_fast = {
    .Mode = SPI_MODE_MASTER,
    .Direction = SPI_DIRECTION_2LINES,
    .DataSize = SPI_DATASIZE_8BIT,
    .CLKPolarity = SPI_POLARITY_LOW,
    .CLKPhase = SPI_PHASE_1EDGE,
    .NSS = SPI_NSS_SOFT,
    .BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2,
    .FirstBit = SPI_FIRSTBIT_MSB,
    .TIMode = SPI_TIMODE_DISABLE,
    .CRCCalculation = SPI_CRCCALCULATION_DISABLE,
    .CRCPolynomial = 7,
    .CRCLength = SPI_CRC_LENGTH_DATASIZE,
    .NSSPMode = SPI_NSS_PULSE_ENABLE,
};

/**
 * SD Card in slow mode (before init)
 */
const SPI_InitTypeDef furi_hal_spi_config_sd_slow = {
    .Mode = SPI_MODE_MASTER,
    .Direction = SPI_DIRECTION_2LINES,
    .DataSize = SPI_DATASIZE_8BIT,
    .CLKPolarity = SPI_POLARITY_LOW,
    .CLKPhase = SPI_PHASE_1EDGE,
    .NSS = SPI_NSS_SOFT,
    .BaudRatePrescaler = SPI_BAUDRATEPRESCALER_32,
    .FirstBit = SPI_FIRSTBIT_MSB,
    .TIMode = SPI_TIMODE_DISABLE,
    .CRCCalculation = SPI_CRCCALCULATION_DISABLE,
    .CRCPolynomial = 7,
    .CRCLength = SPI_CRC_LENGTH_DATASIZE,
    .NSSPMode = SPI_NSS_PULSE_ENABLE,
};

osMutexId_t spi_mutex_d = NULL;
osMutexId_t spi_mutex_r = NULL;

const FuriHalSpiBus spi_r = {
    .spi=&SPI_R,
    .mutex=&spi_mutex_r,
    .miso=&gpio_spi_r_miso,
    .mosi=&gpio_spi_r_mosi,
    .clk=&gpio_spi_r_sck,
};

const FuriHalSpiBus spi_d = {
    .spi=&SPI_D,
    .mutex=&spi_mutex_d,
    .miso=&gpio_spi_d_miso,
    .mosi=&gpio_spi_d_mosi,
    .clk=&gpio_spi_d_sck,
};

const FuriHalSpiDevice furi_hal_spi_devices[FuriHalSpiDeviceIdMax] = {
    { .bus=&spi_r, .config=&furi_hal_spi_config_subghz, .chip_select=&gpio_subghz_cs, },
    { .bus=&spi_d, .config=&furi_hal_spi_config_display, .chip_select=&gpio_display_cs, },
    { .bus=&spi_d, .config=&furi_hal_spi_config_sd_fast, .chip_select=&gpio_sdcard_cs, },
    { .bus=&spi_d, .config=&furi_hal_spi_config_sd_slow, .chip_select=&gpio_sdcard_cs, },
    { .bus=&spi_r, .config=&furi_hal_spi_config_nfc, .chip_select=&gpio_nfc_cs },
};