flipperzero-firmware/lib/ST25RFAL002/source/custom_analog_config.c

778 lines
24 KiB
C
Raw Normal View History

#include "rfal_analogConfigTbl.h"
const uint8_t rfalAnalogConfigCustomSettings[] = {
/****** Default Analog Configuration for Chip-Specific Reset ******/
MODE_ENTRY_16_REG(
(RFAL_ANALOG_CONFIG_TECH_CHIP | RFAL_ANALOG_CONFIG_CHIP_INIT),
ST25R3916_REG_IO_CONF1,
(ST25R3916_REG_IO_CONF1_out_cl_mask | ST25R3916_REG_IO_CONF1_lf_clk_off),
0x07 /* Disable MCU_CLK */
,
ST25R3916_REG_IO_CONF2,
(ST25R3916_REG_IO_CONF2_miso_pd1 | ST25R3916_REG_IO_CONF2_miso_pd2),
0x18 /* SPI Pull downs */
// , ST25R3916_REG_IO_CONF2, ST25R3916_REG_IO_CONF2_aat_en, ST25R3916_REG_IO_CONF2_aat_en /* Enable AAT */
,
ST25R3916_REG_TX_DRIVER,
ST25R3916_REG_TX_DRIVER_d_res_mask,
0x00 /* Set RFO resistance Active Tx */
,
ST25R3916_REG_RES_AM_MOD,
0xFF,
0x80 /* Use minimum non-overlap */
,
ST25R3916_REG_FIELD_THRESHOLD_ACTV,
ST25R3916_REG_FIELD_THRESHOLD_ACTV_trg_mask,
ST25R3916_REG_FIELD_THRESHOLD_ACTV_trg_105mV /* Lower activation threshold (higher than deactivation)*/
,
ST25R3916_REG_FIELD_THRESHOLD_ACTV,
ST25R3916_REG_FIELD_THRESHOLD_ACTV_rfe_mask,
ST25R3916_REG_FIELD_THRESHOLD_ACTV_rfe_105mV /* Lower activation threshold (higher than deactivation)*/
,
ST25R3916_REG_FIELD_THRESHOLD_DEACTV,
ST25R3916_REG_FIELD_THRESHOLD_DEACTV_trg_mask,
ST25R3916_REG_FIELD_THRESHOLD_DEACTV_trg_75mV /* Lower deactivation threshold */
,
ST25R3916_REG_FIELD_THRESHOLD_DEACTV,
ST25R3916_REG_FIELD_THRESHOLD_DEACTV_rfe_mask,
ST25R3916_REG_FIELD_THRESHOLD_DEACTV_rfe_75mV /* Lower deactivation threshold */
,
ST25R3916_REG_AUX_MOD,
ST25R3916_REG_AUX_MOD_lm_ext,
ST25R3916_REG_AUX_MOD_lm_ext /* Disable External Load Modulation */
,
ST25R3916_REG_AUX_MOD,
ST25R3916_REG_AUX_MOD_lm_dri,
ST25R3916_REG_AUX_MOD_lm_dri /* Use internal Load Modulation */
,
ST25R3916_REG_PASSIVE_TARGET,
ST25R3916_REG_PASSIVE_TARGET_fdel_mask,
(5U
<< ST25R3916_REG_PASSIVE_TARGET_fdel_shift) /* Adjust the FDT to be aligned with the bitgrid */
,
ST25R3916_REG_PT_MOD,
(ST25R3916_REG_PT_MOD_ptm_res_mask | ST25R3916_REG_PT_MOD_pt_res_mask),
0x0f /* Reduce RFO resistance in Modulated state */
,
ST25R3916_REG_EMD_SUP_CONF,
ST25R3916_REG_EMD_SUP_CONF_rx_start_emv,
ST25R3916_REG_EMD_SUP_CONF_rx_start_emv_on /* Enable start on first 4 bits */
,
ST25R3916_REG_ANT_TUNE_A,
0xFF,
0x82 /* Set Antenna Tuning (Poller): ANTL */
,
ST25R3916_REG_ANT_TUNE_B,
0xFF,
0x82 /* Set Antenna Tuning (Poller): ANTL */
,
0x84U,
0x10,
0x10 /* Avoid chip internal overheat protection */
)
/****** Default Analog Configuration for Chip-Specific Poll Common ******/
,
MODE_ENTRY_9_REG(
(RFAL_ANALOG_CONFIG_TECH_CHIP | RFAL_ANALOG_CONFIG_CHIP_POLL_COMMON),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
,
ST25R3916_REG_TX_DRIVER,
ST25R3916_REG_TX_DRIVER_am_mod_mask,
ST25R3916_REG_TX_DRIVER_am_mod_12percent /* Set Modulation index */
,
ST25R3916_REG_AUX_MOD,
(ST25R3916_REG_AUX_MOD_dis_reg_am | ST25R3916_REG_AUX_MOD_res_am),
0x00 /* Use AM via regulator */
,
ST25R3916_REG_ANT_TUNE_A,
0xFF,
0x82 /* Set Antenna Tuning (Poller): ANTL */
,
ST25R3916_REG_ANT_TUNE_B,
0xFF,
0x82 /* Set Antenna Tuning (Poller): ANTL */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x00 /* Disable Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x00 /* Disable Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x00 /* Disable Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x00 /* Disable Undershoot Protection */
)
/****** Default Analog Configuration for Poll NFC-A Rx Common ******/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_AUX,
ST25R3916_REG_AUX_dis_corr,
ST25R3916_REG_AUX_dis_corr_correlator /* Use Correlator Receiver */
)
/****** Default Analog Configuration for Poll NFC-A Tx 106 ******/
,
MODE_ENTRY_5_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_106 |
RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_ook /* Use OOK */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x40 /* Set default Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x03 /* Set default Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x40 /* Set default Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x03 /* Set default Undershoot Protection */
)
/****** Default Analog Configuration for Poll NFC-A Rx 106 ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_106 |
RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
0xFF,
0x08,
ST25R3916_REG_RX_CONF2,
0xFF,
0x2D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x51,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
/****** Default Analog Configuration for Poll NFC-A Tx 212 ******/
,
MODE_ENTRY_7_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_212 |
RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
,
ST25R3916_REG_AUX_MOD,
(ST25R3916_REG_AUX_MOD_dis_reg_am | ST25R3916_REG_AUX_MOD_res_am),
0x88 /* Use Resistive AM */
,
ST25R3916_REG_RES_AM_MOD,
ST25R3916_REG_RES_AM_MOD_md_res_mask,
0x7F /* Set Resistive modulation */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x40 /* Set default Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x03 /* Set default Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x40 /* Set default Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x03 /* Set default Undershoot Protection */
)
/****** Default Analog Configuration for Poll NFC-A Rx 212 ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_212 |
RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
0xFF,
0x02,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x14,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
/****** Default Analog Configuration for Poll NFC-A Tx 424 ******/
,
MODE_ENTRY_7_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_424 |
RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
,
ST25R3916_REG_AUX_MOD,
(ST25R3916_REG_AUX_MOD_dis_reg_am | ST25R3916_REG_AUX_MOD_res_am),
0x88 /* Use Resistive AM */
,
ST25R3916_REG_RES_AM_MOD,
ST25R3916_REG_RES_AM_MOD_md_res_mask,
0x7F /* Set Resistive modulation */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x40 /* Set default Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x03 /* Set default Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x40 /* Set default Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x03 /* Set default Undershoot Protection */
)
/****** Default Analog Configuration for Poll NFC-A Rx 424 ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_424 |
RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
0xFF,
0x42,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x54,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
/****** Default Analog Configuration for Poll NFC-A Tx 848 ******/
,
MODE_ENTRY_7_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_848 |
RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
,
ST25R3916_REG_TX_DRIVER,
ST25R3916_REG_TX_DRIVER_am_mod_mask,
ST25R3916_REG_TX_DRIVER_am_mod_40percent /* Set Modulation index */
,
ST25R3916_REG_AUX_MOD,
(ST25R3916_REG_AUX_MOD_dis_reg_am | ST25R3916_REG_AUX_MOD_res_am),
0x00 /* Use AM via regulator */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x00 /* Disable Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x00 /* Disable Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x00 /* Disable Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x00 /* Disable Undershoot Protection */
)
/****** Default Analog Configuration for Poll NFC-A Rx 848 ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_848 |
RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
0xFF,
0x42,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x44,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
/****** Default Analog Configuration for Poll NFC-A Anticolision setting ******/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_ANTICOL),
ST25R3916_REG_CORR_CONF1,
ST25R3916_REG_CORR_CONF1_corr_s6,
0x00 /* Set collision detection level different from data */
)
#ifdef RFAL_USE_COHE
/****** Default Analog Configuration for Poll NFC-B Rx Common ******/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_AUX,
ST25R3916_REG_AUX_dis_corr,
ST25R3916_REG_AUX_dis_corr_coherent /* Use Coherent Receiver */
)
#else
/****** Default Analog Configuration for Poll NFC-B Rx Common ******/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_AUX,
ST25R3916_REG_AUX_dis_corr,
ST25R3916_REG_AUX_dis_corr_correlator /* Use Correlator Receiver */
)
#endif /*RFAL_USE_COHE*/
/****** Default Analog Configuration for Poll NFC-B Rx 106 ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_106 |
RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
0xFF,
0x04,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x1B,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
/****** Default Analog Configuration for Poll NFC-B Rx 212 ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_212 |
RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
0xFF,
0x02,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x14,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
/****** Default Analog Configuration for Poll NFC-B Rx 424 ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_424 |
RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
0xFF,
0x42,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x54,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
/****** Default Analog Configuration for Poll NFC-B Rx 848 ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_848 |
RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
0xFF,
0x42,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x44,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
#ifdef RFAL_USE_COHE
/****** Default Analog Configuration for Poll NFC-F Rx Common ******/
,
MODE_ENTRY_7_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCF |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_AUX,
ST25R3916_REG_AUX_dis_corr,
ST25R3916_REG_AUX_dis_corr_coherent /* Use Pulse Receiver */
,
ST25R3916_REG_RX_CONF1,
0xFF,
0x13,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x54,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
#else
/****** Default Analog Configuration for Poll NFC-F Rx Common ******/
,
MODE_ENTRY_7_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCF |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_AUX,
ST25R3916_REG_AUX_dis_corr,
ST25R3916_REG_AUX_dis_corr_correlator /* Use Correlator Receiver */
,
ST25R3916_REG_RX_CONF1,
0xFF,
0x13,
ST25R3916_REG_RX_CONF2,
0xFF,
0x3D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x54,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x00)
#endif /*RFAL_USE_COHE*/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCV | RFAL_ANALOG_CONFIG_BITRATE_1OF4 |
RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_ook /* Use OOK */
)
#ifdef RFAL_USE_COHE
/****** Default Analog Configuration for Poll NFC-V Rx Common ******/
,
MODE_ENTRY_7_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCV |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_AUX,
ST25R3916_REG_AUX_dis_corr,
ST25R3916_REG_AUX_dis_corr_coherent /* Use Pulse Receiver */
,
ST25R3916_REG_RX_CONF1,
0xFF,
0x13,
ST25R3916_REG_RX_CONF2,
0xFF,
0x2D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x13,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x01)
#else
/****** Default Analog Configuration for Poll NFC-V Rx Common ******/
,
MODE_ENTRY_7_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCV |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_AUX,
ST25R3916_REG_AUX_dis_corr,
ST25R3916_REG_AUX_dis_corr_correlator /* Use Correlator Receiver */
,
ST25R3916_REG_RX_CONF1,
0xFF,
0x13,
ST25R3916_REG_RX_CONF2,
0xFF,
0x2D,
ST25R3916_REG_RX_CONF3,
0xFF,
0x00,
ST25R3916_REG_RX_CONF4,
0xFF,
0x00,
ST25R3916_REG_CORR_CONF1,
0xFF,
0x13,
ST25R3916_REG_CORR_CONF2,
0xFF,
0x01)
#endif /*RFAL_USE_COHE*/
/****** Default Analog Configuration for Poll AP2P Tx 106 ******/
,
MODE_ENTRY_5_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_106 |
RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_ook /* Use OOK modulation */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x40 /* Set default Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x03 /* Set default Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x40 /* Set default Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x03 /* Set default Undershoot Protection */
)
/****** Default Analog Configuration for Poll AP2P Tx 212 ******/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_212 |
RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
)
/****** Default Analog Configuration for Poll AP2P Tx 424 ******/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_424 |
RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
)
/****** Default Analog Configuration for Chip-Specific Listen On ******/
,
MODE_ENTRY_6_REG(
(RFAL_ANALOG_CONFIG_TECH_CHIP | RFAL_ANALOG_CONFIG_CHIP_LISTEN_ON),
ST25R3916_REG_ANT_TUNE_A,
0xFF,
0x00 /* Set Antenna Tuning (Listener): ANTL */
,
ST25R3916_REG_ANT_TUNE_B,
0xFF,
0xff /* Set Antenna Tuning (Listener): ANTL */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x00 /* Disable Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x00 /* Disable Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x00 /* Disable Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x00 /* Disable Undershoot Protection */
)
/****** Default Analog Configuration for Listen AP2P Tx Common ******/
,
MODE_ENTRY_7_REG(
(RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_ANT_TUNE_A,
0xFF,
0x82 /* Set Antenna Tuning (Poller): ANTL */
,
ST25R3916_REG_ANT_TUNE_B,
0xFF,
0x82 /* Set Antenna Tuning (Poller): ANTL */
,
ST25R3916_REG_TX_DRIVER,
ST25R3916_REG_TX_DRIVER_am_mod_mask,
ST25R3916_REG_TX_DRIVER_am_mod_12percent /* Set Modulation index */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x00 /* Disable Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x00 /* Disable Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x00 /* Disable Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x00 /* Disable Undershoot Protection */
)
/****** Default Analog Configuration for Listen AP2P Rx Common ******/
,
MODE_ENTRY_3_REG(
(RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P |
RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX),
ST25R3916_REG_RX_CONF1,
ST25R3916_REG_RX_CONF1_lp_mask,
ST25R3916_REG_RX_CONF1_lp_1200khz /* Set Rx filter configuration */
,
ST25R3916_REG_RX_CONF1,
ST25R3916_REG_RX_CONF1_hz_mask,
ST25R3916_REG_RX_CONF1_hz_12_200khz /* Set Rx filter configuration */
,
ST25R3916_REG_RX_CONF2,
ST25R3916_REG_RX_CONF2_amd_sel,
ST25R3916_REG_RX_CONF2_amd_sel_mixer /* AM demodulator: mixer */
)
/****** Default Analog Configuration for Listen AP2P Tx 106 ******/
,
MODE_ENTRY_5_REG(
(RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P |
RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_ook /* Use OOK modulation */
,
ST25R3916_REG_OVERSHOOT_CONF1,
0xFF,
0x40 /* Set default Overshoot Protection */
,
ST25R3916_REG_OVERSHOOT_CONF2,
0xFF,
0x03 /* Set default Overshoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF1,
0xFF,
0x40 /* Set default Undershoot Protection */
,
ST25R3916_REG_UNDERSHOOT_CONF2,
0xFF,
0x03 /* Set default Undershoot Protection */
)
/****** Default Analog Configuration for Listen AP2P Tx 212 ******/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P |
RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
)
/****** Default Analog Configuration for Listen AP2P Tx 424 ******/
,
MODE_ENTRY_1_REG(
(RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P |
RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_TX),
ST25R3916_REG_MODE,
ST25R3916_REG_MODE_tr_am,
ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
)
};
const uint16_t rfalAnalogConfigCustomSettingsLength = sizeof(rfalAnalogConfigCustomSettings);