flipperzero-firmware/bootloader/targets/f4/stm32wb55xx_flash_cm4.ld

188 lines
5.9 KiB
Plaintext
Raw Normal View History

Firmware, Bootloader: add f3 target. (#215) * Firmware, Bootloader: add f3 target. Refactor code to be portable across targets. * Firmware: remove bkpt * Makefile: debug agent. Debug: f3 platform throw openocd. * freertos-openocd helper * separate hal resources * return of input_dump app * using hew target resources abstration layer for backlight and blink * dirty hack for input driver, f3 has no charging pin * worked input interrupts * working display * F3: switch to 32mHz resonator * F3: configure SD_CS pin * NFC: port to F3. * fat uart app * sd card hal api * separate CC1101 spi config * faster spi gpio for sd card * Assets: disable LFS * Cube: disable css on LSE * Input: format code * Make: add bootloader source code to formatting rule * F3: enable rf by default, adjust clock settings, map all pins where they should be. * libs for coreglitch_demo_0 * nvic priority * bus clocks all to 64 * lf-rfid timer and pin * irda * ir rx setup * tim2 irq handler * Makefile: environment aware mkdir * Makefile, Irukagotchi: commit seq number. * split falling and rising ir rx events * Makefile: proper git branch detect on old git. Firmware: api fix. * fix irda * Makefile,Irukagotchi: date timestamp. * NFC: adjust SPI speed * Irukagotchi: format code * Make: add blackmagic debug in host mode * Makefile: detach blackmagic from terminal signals * Makefile,Irukagotchi: stamp target * add F3 bootloader/firmware to CI Co-authored-by: Aleksandr Kutuzov <aku@plooks.com> Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com> Co-authored-by: aanper <mail@s3f.ru>
2020-11-06 10:52:50 +00:00
/**
*****************************************************************************
**
** File : stm32wb55xx_flash_cm4.ld
**
** Abstract : System Workbench Minimal System calls file
**
** For more information about which c-functions
** need which of these lowlevel functions
** please consult the Newlib libc-manual
**
** Environment : System Workbench for MCU
**
** Distribution: The file is distributed “as is,” without any warranty
** of any kind.
**
*****************************************************************************
**
** <h2><center>&copy; COPYRIGHT(c) 2019 Ac6</center></h2>
**
** Redistribution and use in source and binary forms, with or without modification,
** are permitted provided that the following conditions are met:
** 1. Redistributions of source code must retain the above copyright notice,
** this list of conditions and the following disclaimer.
** 2. Redistributions in binary form must reproduce the above copyright notice,
** this list of conditions and the following disclaimer in the documentation
** and/or other materials provided with the distribution.
** 3. Neither the name of Ac6 nor the names of its contributors
** may be used to endorse or promote products derived from this software
** without specific prior written permission.
**
** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
**
*****************************************************************************
*/
/* Entry Point */
ENTRY(Reset_Handler)
/* Highest address of the user mode stack */
_estack = 0x20030000; /* end of RAM */
/* Generate a link error if heap and stack don't fit into RAM */
_Min_Heap_Size = 0x200; /* required amount of heap */
_Min_Stack_Size = 0x400; /* required amount of stack */
/* Specify the memory areas */
MEMORY
{
FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 32K
Firmware, Bootloader: add f3 target. (#215) * Firmware, Bootloader: add f3 target. Refactor code to be portable across targets. * Firmware: remove bkpt * Makefile: debug agent. Debug: f3 platform throw openocd. * freertos-openocd helper * separate hal resources * return of input_dump app * using hew target resources abstration layer for backlight and blink * dirty hack for input driver, f3 has no charging pin * worked input interrupts * working display * F3: switch to 32mHz resonator * F3: configure SD_CS pin * NFC: port to F3. * fat uart app * sd card hal api * separate CC1101 spi config * faster spi gpio for sd card * Assets: disable LFS * Cube: disable css on LSE * Input: format code * Make: add bootloader source code to formatting rule * F3: enable rf by default, adjust clock settings, map all pins where they should be. * libs for coreglitch_demo_0 * nvic priority * bus clocks all to 64 * lf-rfid timer and pin * irda * ir rx setup * tim2 irq handler * Makefile: environment aware mkdir * Makefile, Irukagotchi: commit seq number. * split falling and rising ir rx events * Makefile: proper git branch detect on old git. Firmware: api fix. * fix irda * Makefile,Irukagotchi: date timestamp. * NFC: adjust SPI speed * Irukagotchi: format code * Make: add blackmagic debug in host mode * Makefile: detach blackmagic from terminal signals * Makefile,Irukagotchi: stamp target * add F3 bootloader/firmware to CI Co-authored-by: Aleksandr Kutuzov <aku@plooks.com> Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com> Co-authored-by: aanper <mail@s3f.ru>
2020-11-06 10:52:50 +00:00
RAM1 (xrw) : ORIGIN = 0x20000004, LENGTH = 0x2FFFC
RAM_SHARED (xrw) : ORIGIN = 0x20030000, LENGTH = 10K
}
/* Define output sections */
SECTIONS
{
/* The startup code goes first into FLASH */
.isr_vector :
{
. = ALIGN(4);
KEEP(*(.isr_vector)) /* Startup code */
. = ALIGN(4);
} >FLASH
/* The program code and other data goes into FLASH */
.text :
{
. = ALIGN(4);
*(.text) /* .text sections (code) */
*(.text*) /* .text* sections (code) */
*(.glue_7) /* glue arm to thumb code */
*(.glue_7t) /* glue thumb to arm code */
*(.eh_frame)
KEEP (*(.init))
KEEP (*(.fini))
. = ALIGN(4);
_etext = .; /* define a global symbols at end of code */
} >FLASH
/* Constant data goes into FLASH */
.rodata :
{
. = ALIGN(4);
*(.rodata) /* .rodata sections (constants, strings, etc.) */
*(.rodata*) /* .rodata* sections (constants, strings, etc.) */
. = ALIGN(4);
} >FLASH
.ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
.ARM : {
__exidx_start = .;
*(.ARM.exidx*)
__exidx_end = .;
} >FLASH
.preinit_array :
{
PROVIDE_HIDDEN (__preinit_array_start = .);
KEEP (*(.preinit_array*))
PROVIDE_HIDDEN (__preinit_array_end = .);
} >FLASH
.init_array :
{
PROVIDE_HIDDEN (__init_array_start = .);
KEEP (*(SORT(.init_array.*)))
KEEP (*(.init_array*))
PROVIDE_HIDDEN (__init_array_end = .);
} >FLASH
.fini_array :
{
PROVIDE_HIDDEN (__fini_array_start = .);
KEEP (*(SORT(.fini_array.*)))
KEEP (*(.fini_array*))
PROVIDE_HIDDEN (__fini_array_end = .);
} >FLASH
/* used by the startup to initialize data */
_sidata = LOADADDR(.data);
/* Initialized data sections goes into RAM, load LMA copy after code */
.data :
{
. = ALIGN(4);
_sdata = .; /* create a global symbol at data start */
*(.data) /* .data sections */
*(.data*) /* .data* sections */
. = ALIGN(4);
_edata = .; /* define a global symbol at data end */
} >RAM1 AT> FLASH
/* Uninitialized data section */
. = ALIGN(4);
.bss :
{
/* This is used by the startup in order to initialize the .bss secion */
_sbss = .; /* define a global symbol at bss start */
__bss_start__ = _sbss;
*(.bss)
*(.bss*)
*(COMMON)
. = ALIGN(4);
_ebss = .; /* define a global symbol at bss end */
__bss_end__ = _ebss;
} >RAM1
/* User_heap_stack section, used to check that there is enough RAM left */
._user_heap_stack :
{
. = ALIGN(8);
PROVIDE ( end = . );
PROVIDE ( _end = . );
. = . + _Min_Heap_Size;
. = . + _Min_Stack_Size;
. = ALIGN(8);
} >RAM1
/* Remove information from the standard libraries */
/DISCARD/ :
{
libc.a ( * )
libm.a ( * )
libgcc.a ( * )
}
.ARM.attributes 0 : { *(.ARM.attributes) }
MAPPING_TABLE (NOLOAD) : { *(MAPPING_TABLE) } >RAM_SHARED
MB_MEM1 (NOLOAD) : { *(MB_MEM1) } >RAM_SHARED
MB_MEM2 (NOLOAD) : { _sMB_MEM2 = . ; *(MB_MEM2) ; _eMB_MEM2 = . ; } >RAM_SHARED
}