Update KeyCombo.md (#2213)

Grammatical corrections and changes
This commit is contained in:
Zoë Prosvetova 2022-12-28 15:39:36 +01:00 committed by GitHub
parent 27ee0f73f7
commit 4accce93cf
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23

View File

@ -1,6 +1,6 @@
# Key Combos # Key Combos
There are times when your flipper feels blue and doesn't respond to your commands. There are times when your Flipper feels blue and doesn't respond to your commands.
In that case, you may find this guide useful. In that case, you may find this guide useful.
@ -12,10 +12,10 @@ In that case, you may find this guide useful.
- Press `LEFT` and `BACK` and hold for a couple of seconds - Press `LEFT` and `BACK` and hold for a couple of seconds
- Release `LEFT` and `BACK` - Release `LEFT` and `BACK`
This combo performs hardware reset by pulling MCU reset line down. This combo performs a hardware reset by pulling MCU reset line down.
Main components involved: Keys -> DD8(NC7SZ32M5X, OR-gate) -> DD1(STM32WB55, MCU) Main components involved: Keys -> DD8(NC7SZ32M5X, OR-gate) -> DD1(STM32WB55, MCU)
There is 1 case when it's not working: There is 1 case where it does not work:
- MCU debug block is active and holding reset line from inside. - MCU debug block is active and holding reset line from inside.
@ -25,32 +25,32 @@ There is 1 case when it's not working:
- Disconnect USB and any external power supplies - Disconnect USB and any external power supplies
- Disconnect USB once again - Disconnect USB once again
- Make sure that you've disconnected USB and any external power supplies - Make sure that you've disconnected USB and any external power supplies
- Press `BACK` and hold for 30 seconds (Only will work with USB Disconnected) - Press `BACK` and hold for 30 seconds (Will only work with USB disconnected)
- If you have not disconnected USB, then disconnect USB and repeat previous step - If you have not disconnected USB, then disconnect USB and repeat previous step
- Release `BACK` key - Release `BACK` key
This combo performs a reset by switching SYS power line off and then on. This combo performs a reset by switching SYS power line off and then on.
Main components involved: Keys -> DD6(bq25896, charger) Main components involved: Keys -> DD6(bq25896, charger)
There is 1 case when it's not working: There is 1 case where it does not work:
- Power supply is connected to USB or 5V_ext - Power supply is connected to USB or 5V_ext
### Software DFU ### Software DFU
- Press `LEFT` on boot to enter DFU with flipper boot-loader - Press `LEFT` on boot to enter DFU with Flipper boot-loader
There is 1 case when it's not working: There is 1 case where it does not work:
- Flipper Boot-loader is damaged or absent - Flipper boot-loader is damaged or absent
### Hardware DFU ### Hardware DFU
- Press `OK` on boot to enter DFU with ST boot-loader - Press `OK` on boot to enter DFU with ST boot-loader
There is 1 case when it's not working: There is 1 case where it does not work:
- Option Bytes are damaged or set to ignore `OK` key - Option Bytes are damaged or set to ignore `OK` key
@ -65,25 +65,25 @@ There is 1 case when it's not working:
- Device will enter DFU with indication (Blue LED + DFU Screen) - Device will enter DFU with indication (Blue LED + DFU Screen)
- Release `LEFT` - Release `LEFT`
This combo performs hardware reset by pulling MCU reset line down. This combo performs a hardware reset by pulling MCU reset line down.
Then `LEFT` key indicates to boot-loader that DFU mode is requested. Then, `LEFT` key indicates to the boot-loader that DFU mode is requested.
There are 2 cases when it's not working: There are 2 cases where it does not work:
- MCU debug block is active and holding reset line from inside - MCU debug block is active and holding reset line from inside
- Flipper Boot-loader is damaged or absent - Flipper boot-loader is damaged or absent
### Hardware Reset + Hardware DFU ### Hardware Reset + Hardware DFU
- Press `LEFT` and `BACK` and `OK` and hold for a couple of seconds - Press `LEFT`, `BACK` and `OK` and hold for a couple of seconds
- Release `BACK` and `LEFT` - Release `BACK` and `LEFT`
- Device will enter DFU without indication - Device will enter DFU without indication
This combo performs hardware reset by pulling MCU reset line down. This combo performs a hardware reset by pulling MCU reset line down.
Then `OK` key forces MCU to load internal boot-loader. Then, `OK` key forces MCU to load internal boot-loader.
There are 2 cases when it's not working: There are 2 cases where it does not work:
- MCU debug block is active and holding reset line from inside - MCU debug block is active and holding reset line from inside
- Option Bytes are damaged or set to ignore `OK` key - Option Bytes are damaged or set to ignore `OK` key
@ -96,15 +96,15 @@ There are 2 cases when it's not working:
- Release `BACK` - Release `BACK`
- Device will enter DFU with indication (Blue LED + DFU Screen) - Device will enter DFU with indication (Blue LED + DFU Screen)
- Release `LEFT` - Release `LEFT`
- Plug USB - Plug in USB
This combo performs reset by switching SYS power line off and then on. This combo performs a reset by switching SYS power line off and then on.
Then `LEFT` key indicates to boot-loader that DFU mode requested. Then, `LEFT` key indicates to boot-loader that DFU mode requested.
There are 2 cases when it's not working: There are 2 cases where it does not work:
- Power supply is connected to USB or 5V_ext - Power supply is connected to USB or 5V_ext
- Flipper Boot-loader is damaged or absent - Flipper boot-loader is damaged or absent
### Hardware Power Reset + Hardware DFU ### Hardware Power Reset + Hardware DFU
@ -115,10 +115,10 @@ There are 2 cases when it's not working:
- Device will enter DFU without indication - Device will enter DFU without indication
- Plug USB - Plug USB
This combo performs reset by switching SYS power line off and then on. This combo performs a reset by switching SYS power line off and then on.
Then `OK` key forces MCU to load internal boot-loader. Then, `OK` key forces MCU to load internal boot-loader.
There are 2 cases when it's not working: There are 2 cases where it does not work:
- Power supply is connected to USB or 5V_ext - Power supply is connected to USB or 5V_ext
- Option Bytes are damaged or set to ignore `OK` key - Option Bytes are damaged or set to ignore `OK` key
@ -131,4 +131,4 @@ If none of the described methods were useful:
- Disconnect the battery and connect again (Requires disassembly) - Disconnect the battery and connect again (Requires disassembly)
- Try to Flash device with ST-Link or other programmer that supports SWD - Try to Flash device with ST-Link or other programmer that supports SWD
If you still here and your device is not working: it's not a software issue. If you still are here and your device is not working: it's not a software issue.