[FL-873] Add F5 target, lp5562 driver and api-hal-light (#347)

* Add F5 target, lp5562 driver and api-hal-light. Update api-usage, switch to F5 by default.
* API HAL: add i2c and hardware version api. Dolphin: show hardware version.
* OTP version generator and flashing utility.
* Assets script: fix code formatting
* Backport F5 changes to F4
* F4: disable insomnia, prevent damage to BLE RX path
* F5 HAL API Light: remove magic delay to fix magic BLE
* Dolphin: HW target validation on start
* invert RSSI indication in sub-1
* API HAL: rename board to body in version api
* Gpio tester: detach and release viewport on exit

Co-authored-by: aanper <mail@s3f.ru>

firmware/targets/f5/api-hal/api-hal-spi-config.c

@@ -0,0 +1,68 @@
+#include "main.h"
+#include "api-hal-spi-config.h"
+
+extern SPI_HandleTypeDef SPI_R;
+extern SPI_HandleTypeDef SPI_D;
+
+/**
+ * SD Card in fast mode (after init)
+ */
+const SPIDevice sd_fast_spi = {
+    .spi = &SPI_D,
+    .config = {
+        .Mode = SPI_MODE_MASTER,
+        .Direction = SPI_DIRECTION_2LINES,
+        .DataSize = SPI_DATASIZE_8BIT,
+        .CLKPolarity = SPI_POLARITY_LOW,
+        .CLKPhase = SPI_PHASE_1EDGE,
+        .NSS = SPI_NSS_SOFT,
+        .BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2,
+        .FirstBit = SPI_FIRSTBIT_MSB,
+        .TIMode = SPI_TIMODE_DISABLE,
+        .CRCCalculation = SPI_CRCCALCULATION_DISABLE,
+        .CRCPolynomial = 7,
+        .CRCLength = SPI_CRC_LENGTH_DATASIZE,
+        .NSSPMode = SPI_NSS_PULSE_ENABLE,
+    }};
+
+/**
+ * SD Card in slow mode (before init)
+ */
+const SPIDevice sd_slow_spi = {
+    .spi = &SPI_D,
+    .config = {
+        .Mode = SPI_MODE_MASTER,
+        .Direction = SPI_DIRECTION_2LINES,
+        .DataSize = SPI_DATASIZE_8BIT,
+        .CLKPolarity = SPI_POLARITY_LOW,
+        .CLKPhase = SPI_PHASE_1EDGE,
+        .NSS = SPI_NSS_SOFT,
+        .BaudRatePrescaler = SPI_BAUDRATEPRESCALER_32,
+        .FirstBit = SPI_FIRSTBIT_MSB,
+        .TIMode = SPI_TIMODE_DISABLE,
+        .CRCCalculation = SPI_CRCCALCULATION_DISABLE,
+        .CRCPolynomial = 7,
+        .CRCLength = SPI_CRC_LENGTH_DATASIZE,
+        .NSSPMode = SPI_NSS_PULSE_ENABLE,
+    }};
+
+/**
+ * Display
+ */
+const SPIDevice display_spi = {
+    .spi = &SPI_D,
+    .config = {
+        .Mode = SPI_MODE_MASTER,
+        .Direction = SPI_DIRECTION_2LINES,
+        .DataSize = SPI_DATASIZE_8BIT,
+        .CLKPolarity = SPI_POLARITY_LOW,
+        .CLKPhase = SPI_PHASE_1EDGE,
+        .NSS = SPI_NSS_SOFT,
+        .BaudRatePrescaler = SPI_BAUDRATEPRESCALER_16,
+        .FirstBit = SPI_FIRSTBIT_MSB,
+        .TIMode = SPI_TIMODE_DISABLE,
+        .CRCCalculation = SPI_CRCCALCULATION_DISABLE,
+        .CRCPolynomial = 7,
+        .CRCLength = SPI_CRC_LENGTH_DATASIZE,
+        .NSSPMode = SPI_NSS_PULSE_ENABLE,
+    }};