/******************************************************************************
* \attention
*
* <h2><center>© COPYRIGHT 2020 STMicroelectronics</center></h2>
*
* Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* www.st.com/myliberty
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
* AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************/
/*
* PROJECT: ST25R391x firmware
* Revision:
* LANGUAGE: ISO C99
*/
/*! \file rfal_nfcv.h
*
* \author Gustavo Patricio
*
* \brief Implementation of NFC-V Poller (ISO15693) device
*
* The definitions and helpers methods provided by this module
* are aligned with NFC-V Digital 2.1
*
*
* \addtogroup RFAL
* @{
*
* \addtogroup RFAL-AL
* \brief RFAL Abstraction Layer
* @{
*
* \addtogroup NFC-V
* \brief RFAL NFC-V Module
* @{
*
*/
#ifndef RFAL_NFCV_H
#define RFAL_NFCV_H
/*
******************************************************************************
* INCLUDES
******************************************************************************
*/
#include "platform.h"
#include "st_errno.h"
#include "rfal_rf.h"
/*
******************************************************************************
* GLOBAL DEFINES
******************************************************************************
*/
#define RFAL_NFCV_UID_LEN 8U /*!< NFC-V UID length */
#define RFAL_NFCV_MAX_BLOCK_LEN \
32U /*!< Max Block size: can be of up to 256 bits ISO 15693 2000 5 */
#define RFAL_NFCV_BNO_LEN 1U /*!< NFC-V Block Number length */
#define RFAL_NFCV_CRC_LEN 2U /*!< NFC-V CRC length */
#define RFAL_NFCV_MAX_GEN_DATA_LEN \
(RFAL_NFCV_MAX_BLOCK_LEN + RFAL_NFCV_BNO_LEN + RFAL_NFCV_UID_LEN) /*!<Max data */
#define RFAL_NFCV_BLOCKNUM_LEN \
1U /*!< Block Number length on normal commands: 8 bits */
#define RFAL_NFCV_BLOCKNUM_EXTENDED_LEN \
2U /*!< Block Number length on extended commands: 16 bits */
#define RFAL_NFCV_PARAM_SKIP \
0U /*!< Skip proprietary Param Request */
/*! NFC-V RequestFlags ISO15693 2000 7.3.1 */
enum {
RFAL_NFCV_REQ_FLAG_DEFAULT =
0x02U, /*!< Default Request Flags */
RFAL_NFCV_REQ_FLAG_SUB_CARRIER =
0x01U, /*!< Sub Carrier flag */
RFAL_NFCV_REQ_FLAG_DATA_RATE =
0x02U, /*!< Data Rate flag */
RFAL_NFCV_REQ_FLAG_INVENTORY =
0x04U, /*!< Inventory flag */
RFAL_NFCV_REQ_FLAG_PROTOCOL_EXT =
0x08U, /*!< Protocol Extension flag */
RFAL_NFCV_REQ_FLAG_SELECT =
0x10U, /*!< Select flag */
RFAL_NFCV_REQ_FLAG_ADDRESS =
0x20U, /*!< Address flag */
RFAL_NFCV_REQ_FLAG_OPTION =
0x40U, /*!< Option flag */
RFAL_NFCV_REQ_FLAG_RFU =
0x80U, /*!< RFU flag */
RFAL_NFCV_REQ_FLAG_AFI =
0x10U, /*!< AFI flag */
RFAL_NFCV_REQ_FLAG_NB_SLOTS =
0x20U, /*!< Number of Slots flag */
};
/*! NFC-V Response Flags ISO15693 2000 7.4.1 */
enum {
RFAL_NFCV_RES_FLAG_ERROR =
0x01U, /*!< Error flag */
RFAL_NFCV_RES_FLAG_RFU1 =
0x02U, /*!< RFU flag */
RFAL_NFCV_RES_FLAG_RFU2 =
0x04U, /*!< RFU flag */
RFAL_NFCV_RES_FLAG_EXTENSION =
0x08U, /*!< Extension flag */
RFAL_NFCV_RES_FLAG_RFU3 =
0x10U, /*!< RFU flag */
RFAL_NFCV_RES_FLAG_RFU4 =
0x20U, /*!< RFU flag */
RFAL_NFCV_RES_FLAG_RFU5 =
0x40U, /*!< RFU flag */
RFAL_NFCV_RES_FLAG_RFU6 =
0x80U /*!< RFU flag */
};
/*! NFC-V Error code ISO15693 2000 7.4.2 */
enum {
RFAL_NFCV_ERROR_CMD_NOT_SUPPORTED =
0x01U, /*!< The command is not supported, code is not recognised */
RFAL_NFCV_ERROR_CMD_NOT_RECOGNIZED =
0x02U, /*!< The command is not recognised, format error occurred */
RFAL_NFCV_ERROR_OPTION_NOT_SUPPORTED =
0x03U, /*!< The option is not supported */
RFAL_NFCV_ERROR_UNKNOWN =
0x0FU, /*!< Unknown error */
RFAL_NFCV_ERROR_BLOCK_NOT_AVALIABLE =
0x10U, /*!< The specified block is not available */
RFAL_NFCV_ERROR_BLOCK_ALREDY_LOCKED =
0x11U, /*!< The specified block is already locked */
RFAL_NFCV_ERROR_BLOCK_LOCKED =
0x12U, /*!< The specified block is locked */
RFAL_NFCV_ERROR_WRITE_FAILED =
0x13U, /*!< The specified block was not successfully programmed */
RFAL_NFCV_ERROR_BLOCK_FAILED =
0x14U /*!< The specified block was not successfully locked */
};
/*! NFC-V command set ISO15693 2000 9.1 */
enum {
RFAL_NFCV_CMD_INVENTORY =
0x01U, /*!< INVENTORY_REQ (Inventory) command */
RFAL_NFCV_CMD_SLPV =
0x02U, /*!< SLPV_REQ (Stay quiet) command */
RFAL_NFCV_CMD_READ_SINGLE_BLOCK =
0x20U, /*!< Read single block command */
RFAL_NFCV_CMD_WRITE_SINGLE_BLOCK =
0x21U, /*!< Write single block command */
RFAL_NFCV_CMD_LOCK_BLOCK =
0x22U, /*!< Lock block command */
RFAL_NFCV_CMD_READ_MULTIPLE_BLOCKS =
0x23U, /*!< Read multiple blocks command */
RFAL_NFCV_CMD_WRITE_MULTIPLE_BLOCKS =
0x24U, /*!< Write multiple blocks command */
RFAL_NFCV_CMD_SELECT =
0x25U, /*!< Select command */
RFAL_NFCV_CMD_RESET_TO_READY =
0x26U, /*!< Reset To Ready command */
RFAL_NFCV_CMD_GET_SYS_INFO =
0x2BU, /*!< Get System Information command */
RFAL_NFCV_CMD_EXTENDED_READ_SINGLE_BLOCK =
0x30U, /*!< Extended read single block command */
RFAL_NFCV_CMD_EXTENDED_WRITE_SINGLE_BLOCK =
0x31U, /*!< Extended write single block command */
RFAL_NFCV_CMD_EXTENDED_LOCK_SINGLE_BLOCK =
0x32U, /*!< Extended lock single block command */
RFAL_NFCV_CMD_EXTENDED_READ_MULTIPLE_BLOCK =
0x33U, /*!< Extended read multiple block command */
RFAL_NFCV_CMD_EXTENDED_WRITE_MULTIPLE_BLOCK =
0x34U, /*!< Extended read multiple block command */
RFAL_NFCV_CMD_EXTENDED_GET_SYS_INFO =
0x3BU /*!< Extended Get System Information command */
};
/*! ST25TV/ST25DV command set */
enum {
RFAL_NFCV_CMD_READ_CONFIGURATION =
0xA0U, /*!< Read configuration command */
RFAL_NFCV_CMD_WRITE_CONFIGURATION =
0xA1U, /*!< Write configuration command */
RFAL_NFCV_CMD_SET_EAS =
0xA2U, /*!< Set EAS command */
RFAL_NFCV_CMD_RESET_EAS =
0xA3U, /*!< Reset EAS command */
RFAL_NFCV_CMD_LOCK_EAS =
0xA4U, /*!< Lock EAS command */
RFAL_NFCV_CMD_ENABLE_EAS =
0xA5U, /*!< Enable EAS command */
RFAL_NFCV_CMD_KILL = 0xA6U, /*!< Kill command */
RFAL_NFCV_CMD_WRITE_EAS_ID =
0xA7U, /*!< Write EAS ID command */
RFAL_NFCV_CMD_WRITE_EAS_CONFIG =
0xA8U, /*!< Write EAS CONFIG command */
RFAL_NFCV_CMD_MANAGE_GPO =
0xA9U, /*!< Manage GPO command */
RFAL_NFCV_CMD_WRITE_MESSAGE =
0xAAU, /*!< Write Message command */
RFAL_NFCV_CMD_READ_MESSAGE_LENGTH =
0xABU, /*!< Read Message Length command */
RFAL_NFCV_CMD_READ_MESSAGE =
0xACU, /*!< Read Message command */
RFAL_NFCV_CMD_READ_DYN_CONFIGURATION =
0xADU, /*!< Read Dynamic Configuration command */
RFAL_NFCV_CMD_WRITE_DYN_CONFIGURATION =
0xAEU, /*!< Write Dynamic Configuration command */
RFAL_NFCV_CMD_WRITE_PASSWORD =
0xB1U, /*!< Write Kill Password / Write Password command */
RFAL_NFCV_CMD_LOCK_KILL =
0xB2U, /*!< Lock Kill command */
RFAL_NFCV_CMD_PRESENT_PASSWORD =
0xB3U, /*!< Present Password command */
RFAL_NFCV_CMD_GET_RANDOM_NUMBER =
0xB4U, /*!< Get Random Number command */
RFAL_NFCV_CMD_FAST_READ_SINGLE_BLOCK =
0xC0U, /*!< Fast Read single block command */
RFAL_NFCV_CMD_FAST_READ_MULTIPLE_BLOCKS =
0xC3U, /*!< Fast Read multiple blocks command */
RFAL_NFCV_CMD_FAST_EXTENDED_READ_SINGLE_BLOCK =
0xC4U, /*!< Fast Extended Read single block command */
RFAL_NFCV_CMD_FAST_EXTENDED_READ_MULTIPLE_BLOCKS =
0xC5U, /*!< Fast Extended Read multiple blocks command */
RFAL_NFCV_CMD_FAST_WRITE_MESSAGE =
0xCAU, /*!< Fast Write Message */
RFAL_NFCV_CMD_FAST_READ_MESSAGE_LENGTH =
0xCBU, /*!< Fast Read Message Length */
RFAL_NFCV_CMD_FAST_READ_MESSAGE =
0xCCU, /*!< Fast Read Message */
RFAL_NFCV_CMD_FAST_READ_DYN_CONFIGURATION =
0xCDU, /*!< Fast Read Dynamic configuration */
RFAL_NFCV_CMD_FAST_WRITE_DYN_CONFIGURATION =
0xCEU /*!< Fast Write Dynamic Configuration */
};
/*! ISO 15693 Get System info parameter request field ISO15693 2018 Table 94 */
enum {
RFAL_NFCV_SYSINFO_DFSID =
0x01U, /*!< Get System info DFSID flag */
RFAL_NFCV_SYSINFO_AFI =
0x02U, /*!< Get System info AFI flag */
RFAL_NFCV_SYSINFO_MEMSIZE =
0x04U, /*!< Get System info MEMSIZE flag */
RFAL_NFCV_SYSINFO_ICREF =
0x08U, /*!< Get System info ICREF flag */
RFAL_NFCV_SYSINFO_MOI =
0x10U, /*!< Get System info MOI flag */
RFAL_NFCV_SYSINFO_CMDLIST =
0x20U, /*!< Get System info CMDLIST flag */
RFAL_NFCV_SYSINFO_CSI =
0x40U, /*!< Get System info CSI flag */
RFAL_NFCV_SYSINFO_REQ_ALL =
0x7FU /*!< Get System info request of all parameters */
};
/*
******************************************************************************
* GLOBAL MACROS
******************************************************************************
*/
/*
******************************************************************************
* GLOBAL TYPES
******************************************************************************
*/
/*! NFC-V Number of slots Digital 2.0 9.6.1 */
typedef enum {
RFAL_NFCV_NUM_SLOTS_1 = 0x20, /*!< Number of slots: 1 */
RFAL_NFCV_NUM_SLOTS_16 = 0x00, /*!< Number of slots: 16 */
} rfalNfcvNumSlots;
/*! NFC-V INVENTORY_RES format Digital 2.0 9.6.2 */
typedef struct {
uint8_t RES_FLAG; /*!< Response Flags */
uint8_t DSFID; /*!< Data Storage Format Identifier */
uint8_t UID[RFAL_NFCV_UID_LEN]; /*!< NFC-V device UID */
uint8_t crc[RFAL_CRC_LEN]; /*!< CRC */
} rfalNfcvInventoryRes;
/*! NFC-V Generic Req format */
typedef struct {
uint8_t REQ_FLAG; /*!< Request Flags */
uint8_t CMD; /*!< Command code */
union { /* PRQA S 0750 # MISRA 19.2 - Both members are of the same type, just different names. Thus no problem can occur. */
uint8_t UID[RFAL_NFCV_UID_LEN]; /*!< Mask Value */
uint8_t data[RFAL_NFCV_MAX_GEN_DATA_LEN]; /*!< Data */
} payload; /*!< Payload */
} rfalNfcvGenericReq;
/*! NFC-V Generic Response format */
typedef struct {
uint8_t RES_FLAG; /*!< Response Flags */
uint8_t data[RFAL_NFCV_MAX_GEN_DATA_LEN]; /*!< Data */
} rfalNfcvGenericRes;
/*! NFC-V listener device (VICC) struct */
typedef struct {
rfalNfcvInventoryRes InvRes; /*!< INVENTORY_RES */
bool isSleep; /*!< Device sleeping flag */
} rfalNfcvListenDevice;
/*
******************************************************************************
* GLOBAL FUNCTION PROTOTYPES
******************************************************************************
*/
/*!
*****************************************************************************
* \brief Initialize NFC-V Poller mode
*
* This methods configures RFAL RF layer to perform as a
* NFC-F Poller/RW (ISO15693) including all default timings
*
* \return ERR_WRONG_STATE : RFAL not initialized or mode not set
* \return ERR_PARAM : Incorrect bitrate
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerInitialize(void);
/*!
*****************************************************************************
* \brief NFC-V Poller Check Presence
*
* This method checks if a NFC-V Listen device (VICC) is present on the field
* by sending an Inventory (INVENTORY_REQ)
*
* \param[out] invRes : If received, the INVENTORY_RES
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_TIMEOUT : Timeout error, no listener device detectedd
* \return ERR_NONE : No error, one or more device in the field
*****************************************************************************
*/
ReturnCode rfalNfcvPollerCheckPresence(rfalNfcvInventoryRes* invRes);
/*!
*****************************************************************************
* \brief NFC-F Poller Poll
*
* This function sends to all VICCs in field the INVENTORY command with the
* given number of slots
*
* If more than one slot is used the following EOF need to be handled
* by the caller using rfalISO15693TransceiveEOFAnticollision()
*
* \param[in] nSlots : Number of Slots to be sent (1 or 16)
* \param[in] maskLen : Number bits on the Mask value
* \param[in] maskVal : location of the Mask value
* \param[out] invRes : location to place the INVENTORY_RES
* \param[out] rcvdLen : number of bits received (without collision)
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_RF_COLLISION : Collision detected
* \return ERR_CRC : CRC error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerInventory(
rfalNfcvNumSlots nSlots,
uint8_t maskLen,
const uint8_t* maskVal,
rfalNfcvInventoryRes* invRes,
uint16_t* rcvdLen);
/*!
*****************************************************************************
* \brief NFC-V Poller Full Collision Resolution
*
* Performs a full Collision resolution as defined in Activity 2.0 9.3.7
* Once done, the devCnt will indicate how many (if any) devices have
* been identified and their details are contained on nfcvDevList
*
* \param[in] compMode : compliance mode to be performed
* \param[in] devLimit : device limit value, and size nfcaDevList
* \param[out] nfcvDevList : NFC-v listener devices list
* \param[out] devCnt : Devices found counter
*
* When compMode is set to ISO the function immediately goes to 16 slots improving
* chances to detect more than only one strong card.
*
* \return ERR_WRONG_STATE : RFAL not initialized or mode not set
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerCollisionResolution(
rfalComplianceMode compMode,
uint8_t devLimit,
rfalNfcvListenDevice* nfcvDevList,
uint8_t* devCnt);
/*!
*****************************************************************************
* \brief NFC-V Poller Full Collision Resolution With Sleep
*
* Performs a full Collision resolution which is different from Activity 2.0 9.3.7.
* The implementation uses SLPV (StayQuiet) command to make sure all cards are found.
* Once done, the devCnt will indicate how many (if any) devices have
* been identified and their details are contained on nfcvDevList
*
* \param[in] devLimit : device limit value, and size nfcaDevList
* \param[out] nfcvDevList : NFC-v listener devices list
* \param[out] devCnt : Devices found counter
*
* \return ERR_WRONG_STATE : RFAL not initialized or mode not set
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerSleepCollisionResolution(
uint8_t devLimit,
rfalNfcvListenDevice* nfcvDevList,
uint8_t* devCnt);
/*!
*****************************************************************************
* \brief NFC-V Poller Sleep
*
* This function is used to send the SLPV_REQ (Stay Quiet) command to put the VICC
* with the given UID to state QUIET so that they do not reply to more Inventory
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to Sleep
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerSleep(uint8_t flags, const uint8_t* uid);
/*!
*****************************************************************************
* \brief NFC-V Poller Select
*
* Selects a device (VICC) by its UID
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be Selected
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerSelect(uint8_t flags, const uint8_t* uid);
/*!
*****************************************************************************
* \brief NFC-V Poller Read Single Block
*
* Reads a Single Block from a device (VICC)
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[in] blockNum : Number of the block to read
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerReadSingleBlock(
uint8_t flags,
const uint8_t* uid,
uint8_t blockNum,
uint8_t* rxBuf,
uint16_t rxBufLen,
uint16_t* rcvLen);
/*!
*****************************************************************************
* \brief NFC-V Poller Write Single Block
*
* Writes a Single Block from a device (VICC)
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be written
* if UID is provided Addressed mode will be used
* \param[in] blockNum : Number of the block to write
* \param[in] wrData : data to be written on the given block
* \param[in] blockLen : number of bytes of a block
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerWriteSingleBlock(
uint8_t flags,
const uint8_t* uid,
uint8_t blockNum,
const uint8_t* wrData,
uint8_t blockLen);
/*!
*****************************************************************************
* \brief NFC-V Poller Read Multiple Blocks
*
* Reads Multiple Blocks from a device (VICC)
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[in] firstBlockNum : first block to be read
* \param[in] numOfBlocks : number of block to read
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerReadMultipleBlocks(
uint8_t flags,
const uint8_t* uid,
uint8_t firstBlockNum,
uint8_t numOfBlocks,
uint8_t* rxBuf,
uint16_t rxBufLen,
uint16_t* rcvLen);
/*!
*****************************************************************************
* \brief NFC-V Poller Write Multiple Blocks
*
* Reads Multiple Blocks from a device (VICC)
* In order to not limit the length of the Write multiple command, a buffer
* must be provided where the request will be composed and then sent.
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[in] firstBlockNum : first block to be write
* \param[in] numOfBlocks : number of consecutive blocks to write
* \param[in] txBuf : buffer where the request will be composed
* \param[in] txBufLen : length of txBuf
* \param[in] blockLen : number of bytes of a block
* \param[in] wrData : data to be written
* \param[in] wrDataLen : length of the data do be written. Must be
* aligned with number of blocks to write and
* the size of a block
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerWriteMultipleBlocks(
uint8_t flags,
const uint8_t* uid,
uint8_t firstBlockNum,
uint8_t numOfBlocks,
uint8_t* txBuf,
uint16_t txBufLen,
uint8_t blockLen,
const uint8_t* wrData,
uint16_t wrDataLen);
/*!
*****************************************************************************
* \brief NFC-V Poller Extended Lock Single Block
*
* Blocks a Single Block from a device (VICC) supporting extended commands
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device
* if UID is provided Addressed mode will be used
* \param[in] blockNum : Number of the block to be locked
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerLockBlock(uint8_t flags, const uint8_t* uid, uint8_t blockNum);
/*!
*****************************************************************************
* \brief NFC-V Poller Extended Lock Single Block
*
* Blocks a Single Block from a device (VICC) supporting extended commands
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device
* if UID is provided Addressed mode will be used
* \param[in] blockNum : Number of the block to be locked (16 bits)
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode
rfalNfcvPollerExtendedLockSingleBlock(uint8_t flags, const uint8_t* uid, uint16_t blockNum);
/*!
*****************************************************************************
* \brief NFC-V Poller Extended Read Single Block
*
* Reads a Single Block from a device (VICC) supporting extended commands
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[in] blockNum : Number of the block to read (16 bits)
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerExtendedReadSingleBlock(
uint8_t flags,
const uint8_t* uid,
uint16_t blockNum,
uint8_t* rxBuf,
uint16_t rxBufLen,
uint16_t* rcvLen);
/*!
*****************************************************************************
* \brief NFC-V Poller Extended Write Single Block
*
* Writes a Single Block from a device (VICC) supporting extended commands
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device
* if UID is provided Addressed mode will be used
* \param[in] blockNum : Number of the block to write (16 bits)
* \param[in] wrData : data to be written on the given block
* \param[in] blockLen : number of bytes of a block
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerExtendedWriteSingleBlock(
uint8_t flags,
const uint8_t* uid,
uint16_t blockNum,
const uint8_t* wrData,
uint8_t blockLen);
/*!
*****************************************************************************
* \brief NFC-V Poller Extended Read Multiple Blocks
*
* Reads Multiple Blocks from a device (VICC) supporting extended commands
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[in] firstBlockNum : first block to be read (16 bits)
* \param[in] numOfBlocks : number of consecutive blocks to read (16 bits)
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerExtendedReadMultipleBlocks(
uint8_t flags,
const uint8_t* uid,
uint16_t firstBlockNum,
uint16_t numOfBlocks,
uint8_t* rxBuf,
uint16_t rxBufLen,
uint16_t* rcvLen);
/*!
*****************************************************************************
* \brief NFC-V Poller Extended Write Multiple Blocks
*
* Writes Multiple Blocks from a device (VICC) supporting extended commands
* In order to not limit the length of the Write multiple command, a buffer
* must be provided where the request will be composed and then sent.
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[in] firstBlockNum : first block to be write (16 bits)
* \param[in] numOfBlocks : number of consecutive blocks to write (16 bits)
* \param[in] txBuf : buffer where the request will be composed
* \param[in] txBufLen : length of txBuf
* \param[in] blockLen : number of bytes of a block
* \param[in] wrData : data to be written
* \param[in] wrDataLen : length of the data do be written. Must be
* aligned with number of blocks to write and
* the size of a block
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerExtendedWriteMultipleBlocks(
uint8_t flags,
const uint8_t* uid,
uint16_t firstBlockNum,
uint16_t numOfBlocks,
uint8_t* txBuf,
uint16_t txBufLen,
uint8_t blockLen,
const uint8_t* wrData,
uint16_t wrDataLen);
/*!
*****************************************************************************
* \brief NFC-V Get System Information
*
* Sends Get System Information command
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerGetSystemInformation(
uint8_t flags,
const uint8_t* uid,
uint8_t* rxBuf,
uint16_t rxBufLen,
uint16_t* rcvLen);
/*!
*****************************************************************************
* \brief NFC-V Extended Get System Information
*
* Sends Extended Get System Information command
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[in] requestField : Get System info parameter request field
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerExtendedGetSystemInformation(
uint8_t flags,
const uint8_t* uid,
uint8_t requestField,
uint8_t* rxBuf,
uint16_t rxBufLen,
uint16_t* rcvLen);
/*!
*****************************************************************************
* \brief NFC-V Transceive Request
*
* Performs a generic transceive with an ISO15693 tag
*
* \param[in] cmd : NFC-V command
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] param : Prepend parameter on certain proprietary requests
* For default commands skip: RFAL_NFCV_PARAM_SKIP
* \param[in] uid : UID of the device to be put to be read
* if UID is provided Addressed mode will be used
* \param[in] data : command parameters append after UID
* \param[in] dataLen : command parameters Len
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalNfcvPollerTransceiveReq(
uint8_t cmd,
uint8_t flags,
uint8_t param,
const uint8_t* uid,
const uint8_t* data,
uint16_t dataLen,
uint8_t* rxBuf,
uint16_t rxBufLen,
uint16_t* rcvLen);
#endif /* RFAL_NFCV_H */
/**
* @}
*
* @}
*
* @}
*/