flipperzero-firmware/lib/ST25RFAL002/include/rfal_st25xv.h
2020-10-20 14:12:28 +03:00

730 lines
36 KiB
C
Executable File

/******************************************************************************
* \attention
*
* <h2><center>&copy; COPYRIGHT 2020 STMicroelectronics</center></h2>
*
* Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* www.st.com/myliberty
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
* AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************/
/*
* PROJECT: ST25R391x firmware
* Revision:
* LANGUAGE: ISO C99
*/
/*! \file rfal_st25xv.h
*
* \author Gustavo Patricio
*
* \brief NFC-V ST25 NFC-V Tag specific features
*
* This module provides support for ST's specific features available on
* NFC-V (ISO15693) tag families: ST25D, ST25TV, M24LR
*
*
* \addtogroup RFAL
* @{
*
* \addtogroup RFAL-AL
* \brief RFAL Abstraction Layer
* @{
*
* \addtogroup ST25xV
* \brief RFAL ST25xV Module
* @{
*
*/
#ifndef RFAL_ST25xV_H
#define RFAL_ST25xV_H
/*
******************************************************************************
* INCLUDES
******************************************************************************
*/
#include "platform.h"
#include "st_errno.h"
#include "rfal_nfc.h"
#include "rfal_rf.h"
/*
******************************************************************************
* GLOBAL DEFINES
******************************************************************************
*/
#define RFAL_NFCV_BLOCKNUM_M24LR_LEN 2U /*!< Block Number length of MR24LR tags: 16 bits */
#define RFAL_NFCV_ST_IC_MFG_CODE 0x02 /*!< ST IC Mfg code (used for custom commands) */
/*!
*****************************************************************************
* \brief NFC-V Poller Read Single Block (M24LR)
*
* Reads a Single Block from a M24LR tag which has the number of blocks
* bigger than 256 (M24LR16 ; M24LR64)
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* default: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] blockNum : Number of the block to read (16 bits)
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerM24LRReadSingleBlock( uint8_t flags, const uint8_t* uid, uint16_t blockNum, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Read Single Block (M24LR)
*
* Reads a Single Block from a M24LR tag which has the number of blocks
* bigger than 256 (M24LR16 ; M24LR64) using ST Fast mode
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* default: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] blockNum : Number of the block to read (16 bits)
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerM24LRFastReadSingleBlock( uint8_t flags, const uint8_t* uid, uint16_t blockNum, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Write Single Block (M24LR)
*
* Writes a Single Block from a M24LR tag which has the number of blocks
* bigger than 256 (M24LR16 ; M24LR64)
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be written
* if not provided Select mode will be used
* \param[in] blockNum : Number of the block to write (16 bits)
* \param[in] wrData : data to be written on the given block
* \param[in] blockLen : number of bytes of a block
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerM24LRWriteSingleBlock( uint8_t flags, const uint8_t* uid, uint16_t blockNum, const uint8_t* wrData, uint8_t blockLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Read Multiple Blocks (M24LR)
*
* Reads Multiple Blocks from a device from a M24LR tag which has the number of blocks
* bigger than 256 (M24LR16 ; M24LR64)
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] firstBlockNum : first block to be read (16 bits)
* \param[in] numOfBlocks : number of block to read
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerM24LRReadMultipleBlocks( uint8_t flags, const uint8_t* uid, uint16_t firstBlockNum, uint8_t numOfBlocks, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Read Multiple Blocks (M24LR)
*
* Reads Multiple Blocks from a device from a M24LR tag which has the number of blocks
* bigger than 256 (M24LR16 ; M24LR64) using ST Fast mode
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] firstBlockNum : first block to be read (16 bits)
* \param[in] numOfBlocks : number of block to read
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerM24LRFastReadMultipleBlocks( uint8_t flags, const uint8_t* uid, uint16_t firstBlockNum, uint8_t numOfBlocks, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Read Single Block
*
* Reads a Single Block from a device (VICC) using ST Fast mode
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] blockNum : Number of the block to read
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastReadSingleBlock( uint8_t flags, const uint8_t* uid, uint8_t blockNum, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Read Multiple Blocks
*
* Reads Multiple Blocks from a device (VICC) using ST Fast mode
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] firstBlockNum : first block to be read
* \param[in] numOfBlocks : number of block to read
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastReadMultipleBlocks( uint8_t flags, const uint8_t* uid, uint8_t firstBlockNum, uint8_t numOfBlocks, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Extended Read Single Block
*
* Reads a Single Block from a device (VICC) supporting extended commands using ST Fast mode
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] blockNum : Number of the block to read (16 bits)
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastExtendedReadSingleBlock( uint8_t flags, const uint8_t* uid, uint16_t blockNum, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Extended Read Multiple Blocks
*
* Reads Multiple Blocks from a device (VICC) supporting extended commands using ST Fast mode
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] firstBlockNum : first block to be read (16 bits)
* \param[in] numOfBlocks : number of consecutive blocks to read (16 bits)
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastExtReadMultipleBlocks( uint8_t flags, const uint8_t* uid, uint16_t firstBlockNum, uint16_t numOfBlocks, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Read Configuration
*
* Reads static configuration registers at the Pointer address
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] pointer : Pointer address
* \param[out] regValue : Register value
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerReadConfiguration( uint8_t flags, const uint8_t* uid, uint8_t pointer, uint8_t* regValue );
/*!
*****************************************************************************
* \brief NFC-V Poller Write Configuration
*
* Writes static configuration registers at the Pointer address
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] pointer : Pointer address
* \param[in] regValue : Register value
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerWriteConfiguration( uint8_t flags, const uint8_t* uid, uint8_t pointer, uint8_t regValue );
/*!
*****************************************************************************
* \brief NFC-V Poller Read Dynamic Configuration
*
* Reads dynamic registers at the Pointer address
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] pointer : Pointer address
* \param[out] regValue : Register value
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerReadDynamicConfiguration( uint8_t flags, const uint8_t* uid, uint8_t pointer, uint8_t* regValue );
/*!
*****************************************************************************
* \brief NFC-V Poller Write Dynamic Configuration
*
* Writes dynamic registers at the Pointer address
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] pointer : Pointer address
* \param[in] regValue : Register value
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerWriteDynamicConfiguration( uint8_t flags, const uint8_t* uid, uint8_t pointer, uint8_t regValue );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Read Dynamic Configuration
*
* Reads dynamic registers at the Pointer address using ST Fast mode
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] pointer : Pointer address
* \param[out] regValue : Register value
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastReadDynamicConfiguration( uint8_t flags, const uint8_t* uid, uint8_t pointer, uint8_t* regValue );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Write Dynamic Configuration
*
* Writes dynamic registers at the Pointer address using ST Fast mode
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] pointer : Pointer address
* \param[in] regValue : Register value
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastWriteDynamicConfiguration( uint8_t flags, const uint8_t* uid, uint8_t pointer, uint8_t regValue );
/*!
*****************************************************************************
* \brief NFC-V Poller Present Password
*
* Sends the Present Password command
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] pwdNum : Password number
* \param[in] pwd : Password
* \param[in] pwdLen : Password length
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerPresentPassword( uint8_t flags, const uint8_t* uid, uint8_t pwdNum, const uint8_t* pwd, uint8_t pwdLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Get Random Number
*
* Returns a 16 bit random number
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerGetRandomNumber( uint8_t flags, const uint8_t* uid, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Read Message length
*
* Sends a Read Message Length message to retrieve the value of MB_LEN_Dyn
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[out] msgLen : Message Length
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerReadMessageLength( uint8_t flags, const uint8_t* uid, uint8_t* msgLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Read Message length
*
* Sends a Fast Read Message Length message to retrieve the value of MB_LEN_Dyn using ST Fast mode.
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[out] msgLen : Message Length
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastReadMsgLength( uint8_t flags, const uint8_t* uid, uint8_t* msgLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Read Message
*
* Reads up to 256 bytes in the Mailbox from the location
* specified by MBpointer and sends back their value in the rxBuf response.
* First MailBox location is '00'. When Number of bytes is set to 00h
* and MBPointer is equals to 00h, the MB_LEN bytes of the full message
* are returned. Otherwise, Read Message command returns (Number of Bytes + 1) bytes
* (i.e. 01h returns 2 bytes, FFh returns 256 bytes).
* An error is reported if (Pointer + Nb of bytes + 1) is greater than the message length.
* RF Reading of the last byte of the mailbox message automatically clears b1
* of MB_CTRL_Dyn HOST_PUT_MSG, and allows RF to put a new message.
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] mbPointer : MPpointer
* \param[in] numBytes : number of bytes
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerReadMessage( uint8_t flags, const uint8_t* uid, uint8_t mbPointer, uint8_t numBytes, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Read Message
*
* Reads up to 256 bytes in the Mailbox from the location
* specified by MBpointer and sends back their value in the rxBuf response using ST Fast mode.
* First MailBox location is '00'. When Number of bytes is set to 00h
* and MBPointer is equals to 00h, the MB_LEN bytes of the full message
* are returned. Otherwise, Read Message command returns (Number of Bytes + 1) bytes
* (i.e. 01h returns 2 bytes, FFh returns 256 bytes).
* An error is reported if (Pointer + Nb of bytes + 1) is greater than the message length.
* RF Reading of the last byte of the mailbox message automatically clears b1
* of MB_CTRL_Dyn HOST_PUT_MSG, and allows RF to put a new message.
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] mbPointer : MPpointer
* \param[in] numBytes : number of bytes
* \param[out] rxBuf : buffer to store response (also with RES_FLAGS)
* \param[in] rxBufLen : length of rxBuf
* \param[out] rcvLen : number of bytes received
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastReadMessage( uint8_t flags, const uint8_t* uid, uint8_t mbPointer, uint8_t numBytes, uint8_t* rxBuf, uint16_t rxBufLen, uint16_t *rcvLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Write Message
*
* Sends Write message Command
*
* On receiving the Write Message command, the ST25DVxxx puts the data contained
* in the request into the Mailbox buffer, update the MB_LEN_Dyn register, and
* set bit RF_PUT_MSG in MB_CTRL_Dyn register. It then reports if the write operation was successful
* in the response. The ST25DVxxx Mailbox contains up to 256 data bytes which are filled from the
* first location '00'. MSGlength parameter of the command is the number of
* Data bytes minus 1 (00 for 1 byte of data, FFh for 256 bytes of data).
* Write Message could be executed only when Mailbox is accessible by RF.
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] msgLen : MSGLen number of Data bytes minus 1
* \param[in] msgData : Message Data
* \param[out] txBuf : buffer to used to build the Write Message command
* \param[in] txBufLen : length of txBuf
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerWriteMessage( uint8_t flags, const uint8_t* uid, uint8_t msgLen, const uint8_t* msgData, uint8_t* txBuf, uint16_t txBufLen );
/*!
*****************************************************************************
* \brief NFC-V Poller Fast Write Message
*
* Sends Fast Write message Command using ST Fast mode
*
* On receiving the Write Message command, the ST25DVxxx puts the data contained
* in the request into the Mailbox buffer, update the MB_LEN_Dyn register, and
* set bit RF_PUT_MSG in MB_CTRL_Dyn register. It then reports if the write operation was successful
* in the response. The ST25DVxxx Mailbox contains up to 256 data bytes which are filled from the
* first location '00'. MSGlength parameter of the command is the number of
* Data bytes minus 1 (00 for 1 byte of data, FFh for 256 bytes of data).
* Write Message could be executed only when Mailbox is accessible by RF.
*
* \param[in] flags : Flags to be used: Sub-carrier; Data_rate; Option
* for NFC-Forum use: RFAL_NFCV_REQ_FLAG_DEFAULT
* \param[in] uid : UID of the device to be put to be read
* if not provided Select mode will be used
* \param[in] msgLen : MSGLen number of Data bytes minus 1
* \param[in] msgData : Message Data
* \param[out] txBuf : buffer to used to build the Write Message command
* \param[in] txBufLen : length of txBuf
*
* \return ERR_WRONG_STATE : RFAL not initialized or incorrect mode
* \return ERR_PARAM : Invalid parameters
* \return ERR_IO : Generic internal error
* \return ERR_CRC : CRC error detected
* \return ERR_FRAMING : Framing error detected
* \return ERR_PROTO : Protocol error detected
* \return ERR_TIMEOUT : Timeout error
* \return ERR_NONE : No error
*****************************************************************************
*/
ReturnCode rfalST25xVPollerFastWriteMessage( uint8_t flags, const uint8_t* uid, uint8_t msgLen, const uint8_t* msgData, uint8_t* txBuf, uint16_t txBufLen );
#endif /* RFAL_ST25xV_H */
/**
* @}
*
* @}
*
* @}
*/