68a3f6b4b7
* Add F5 target, lp5562 driver and api-hal-light. Update api-usage, switch to F5 by default. * API HAL: add i2c and hardware version api. Dolphin: show hardware version. * OTP version generator and flashing utility. * Assets script: fix code formatting * Backport F5 changes to F4 * F4: disable insomnia, prevent damage to BLE RX path * F5 HAL API Light: remove magic delay to fix magic BLE * Dolphin: HW target validation on start * invert RSSI indication in sub-1 * API HAL: rename board to body in version api * Gpio tester: detach and release viewport on exit Co-authored-by: aanper <mail@s3f.ru>
198 lines
6.8 KiB
C
198 lines
6.8 KiB
C
/**
|
|
******************************************************************************
|
|
* @file gpio.c
|
|
* @brief This file provides code for the configuration
|
|
* of all used GPIO pins.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2021 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under Ultimate Liberty license
|
|
* SLA0044, the "License"; You may not use this file except in compliance with
|
|
* the License. You may obtain a copy of the License at:
|
|
* www.st.com/SLA0044
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "gpio.h"
|
|
|
|
/* USER CODE BEGIN 0 */
|
|
|
|
/* USER CODE END 0 */
|
|
|
|
/*----------------------------------------------------------------------------*/
|
|
/* Configure GPIO */
|
|
/*----------------------------------------------------------------------------*/
|
|
/* USER CODE BEGIN 1 */
|
|
|
|
/* USER CODE END 1 */
|
|
|
|
/** Configure pins as
|
|
* Analog
|
|
* Input
|
|
* Output
|
|
* EVENT_OUT
|
|
* EXTI
|
|
*/
|
|
void MX_GPIO_Init(void)
|
|
{
|
|
|
|
GPIO_InitTypeDef GPIO_InitStruct = {0};
|
|
|
|
/* GPIO Ports Clock Enable */
|
|
__HAL_RCC_GPIOC_CLK_ENABLE();
|
|
__HAL_RCC_GPIOH_CLK_ENABLE();
|
|
__HAL_RCC_GPIOB_CLK_ENABLE();
|
|
__HAL_RCC_GPIOA_CLK_ENABLE();
|
|
__HAL_RCC_GPIOE_CLK_ENABLE();
|
|
__HAL_RCC_GPIOD_CLK_ENABLE();
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(GPIOA, PA_SW_0_Pin|PA_SW_1_Pin, GPIO_PIN_RESET);
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(PERIPH_POWER_GPIO_Port, PERIPH_POWER_Pin, GPIO_PIN_SET);
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(DISPLAY_RST_GPIO_Port, DISPLAY_RST_Pin, GPIO_PIN_RESET);
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(NFC_CS_GPIO_Port, NFC_CS_Pin, GPIO_PIN_SET);
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(DISPLAY_DI_GPIO_Port, DISPLAY_DI_Pin, GPIO_PIN_RESET);
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(GPIOC, DISPLAY_CS_Pin|SD_CS_Pin, GPIO_PIN_SET);
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(CC1101_CS_GPIO_Port, CC1101_CS_Pin, GPIO_PIN_SET);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = BUTTON_BACK_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING_FALLING;
|
|
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
|
HAL_GPIO_Init(BUTTON_BACK_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = BUTTON_OK_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING_FALLING;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
HAL_GPIO_Init(BUTTON_OK_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pins : PCPin PCPin PCPin PCPin */
|
|
GPIO_InitStruct.Pin = PC0_Pin|PC1_Pin|PC3_Pin|PC10_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pins : PAPin PAPin */
|
|
GPIO_InitStruct.Pin = PA_SW_0_Pin|PA_SW_1_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = PERIPH_POWER_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|
HAL_GPIO_Init(PERIPH_POWER_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pins : PAPin PAPin PAPin */
|
|
GPIO_InitStruct.Pin = PA4_Pin|PA6_Pin|PA7_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = RFID_PULL_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
HAL_GPIO_Init(RFID_PULL_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = CC1101_G0_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING_FALLING;
|
|
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
|
|
HAL_GPIO_Init(CC1101_G0_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pins : PBPin PBPin PBPin */
|
|
GPIO_InitStruct.Pin = PB2_Pin|iBTN_Pin|PB3_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pins : PBPin PBPin PBPin PBPin */
|
|
GPIO_InitStruct.Pin = BUTTON_UP_Pin|BUTTON_LEFT_Pin|BUTTON_DOWN_Pin|BUTTON_RIGHT_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING_FALLING;
|
|
GPIO_InitStruct.Pull = GPIO_PULLUP;
|
|
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = DISPLAY_RST_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|
HAL_GPIO_Init(DISPLAY_RST_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = NFC_CS_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
|
HAL_GPIO_Init(NFC_CS_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pins : PCPin PCPin */
|
|
GPIO_InitStruct.Pin = DISPLAY_DI_Pin|DISPLAY_CS_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = SD_CD_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
HAL_GPIO_Init(SD_CD_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = SD_CS_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
|
HAL_GPIO_Init(SD_CS_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : PtPin */
|
|
GPIO_InitStruct.Pin = CC1101_CS_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
|
HAL_GPIO_Init(CC1101_CS_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/* EXTI interrupt init*/
|
|
HAL_NVIC_SetPriority(EXTI1_IRQn, 5, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI1_IRQn);
|
|
|
|
HAL_NVIC_SetPriority(EXTI3_IRQn, 5, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI3_IRQn);
|
|
|
|
HAL_NVIC_SetPriority(EXTI9_5_IRQn, 5, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI9_5_IRQn);
|
|
|
|
HAL_NVIC_SetPriority(EXTI15_10_IRQn, 5, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI15_10_IRQn);
|
|
|
|
}
|
|
|
|
/* USER CODE BEGIN 2 */
|
|
|
|
/* USER CODE END 2 */
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|