8073992925
* RFID: pull antenna down when emulating * Rfid: fixed HID emulation by adding zero pulse every 4 bits * Rfid: HID emulation fixed with DSP based FSK oscillator. * Rfid: receive 125KHz clock for emulation timer from antenna and comparator * Rfid: commented unused variable * Firmware: rollback changes in f6. * Add F7 target based on F6. * F7/F6: update cube projects, apply changes to the targets, update linker scripts with correct RAM start values. * FuriHal: RFID init routine. * Scripts: update OTP tool for v11 board Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
96 lines
3.0 KiB
C
96 lines
3.0 KiB
C
/**
|
|
******************************************************************************
|
|
* @file usart.c
|
|
* @brief This file provides code for the configuration
|
|
* of the USART instances.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2021 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under Ultimate Liberty license
|
|
* SLA0044, the "License"; You may not use this file except in compliance with
|
|
* the License. You may obtain a copy of the License at:
|
|
* www.st.com/SLA0044
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "usart.h"
|
|
|
|
/* USER CODE BEGIN 0 */
|
|
|
|
/* USER CODE END 0 */
|
|
|
|
/* USART1 init function */
|
|
|
|
void MX_USART1_UART_Init(void)
|
|
{
|
|
|
|
/* USER CODE BEGIN USART1_Init 0 */
|
|
|
|
/* USER CODE END USART1_Init 0 */
|
|
|
|
LL_USART_InitTypeDef USART_InitStruct = {0};
|
|
|
|
LL_GPIO_InitTypeDef GPIO_InitStruct = {0};
|
|
|
|
/* Peripheral clock enable */
|
|
LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_USART1);
|
|
|
|
LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_GPIOB);
|
|
/**USART1 GPIO Configuration
|
|
PB6 ------> USART1_TX
|
|
PB7 ------> USART1_RX
|
|
*/
|
|
GPIO_InitStruct.Pin = LL_GPIO_PIN_6|LL_GPIO_PIN_7;
|
|
GPIO_InitStruct.Mode = LL_GPIO_MODE_ALTERNATE;
|
|
GPIO_InitStruct.Speed = LL_GPIO_SPEED_FREQ_LOW;
|
|
GPIO_InitStruct.OutputType = LL_GPIO_OUTPUT_PUSHPULL;
|
|
GPIO_InitStruct.Pull = LL_GPIO_PULL_NO;
|
|
GPIO_InitStruct.Alternate = LL_GPIO_AF_7;
|
|
LL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
|
|
|
/* USER CODE BEGIN USART1_Init 1 */
|
|
|
|
/* USER CODE END USART1_Init 1 */
|
|
USART_InitStruct.PrescalerValue = LL_USART_PRESCALER_DIV1;
|
|
USART_InitStruct.BaudRate = 115200;
|
|
USART_InitStruct.DataWidth = LL_USART_DATAWIDTH_8B;
|
|
USART_InitStruct.StopBits = LL_USART_STOPBITS_1;
|
|
USART_InitStruct.Parity = LL_USART_PARITY_NONE;
|
|
USART_InitStruct.TransferDirection = LL_USART_DIRECTION_TX;
|
|
USART_InitStruct.HardwareFlowControl = LL_USART_HWCONTROL_NONE;
|
|
USART_InitStruct.OverSampling = LL_USART_OVERSAMPLING_16;
|
|
LL_USART_Init(USART1, &USART_InitStruct);
|
|
LL_USART_SetTXFIFOThreshold(USART1, LL_USART_FIFOTHRESHOLD_1_8);
|
|
LL_USART_SetRXFIFOThreshold(USART1, LL_USART_FIFOTHRESHOLD_1_8);
|
|
LL_USART_DisableFIFO(USART1);
|
|
LL_USART_EnableAutoBaudRate(USART1);
|
|
LL_USART_SetAutoBaudRateMode(USART1, LL_USART_AUTOBAUD_DETECT_ON_STARTBIT);
|
|
LL_USART_ConfigAsyncMode(USART1);
|
|
|
|
/* USER CODE BEGIN WKUPType USART1 */
|
|
|
|
/* USER CODE END WKUPType USART1 */
|
|
|
|
LL_USART_Enable(USART1);
|
|
|
|
/* Polling USART1 initialisation */
|
|
while(!(LL_USART_IsActiveFlag_TEACK(USART1)))
|
|
{
|
|
}
|
|
/* USER CODE BEGIN USART1_Init 2 */
|
|
|
|
/* USER CODE END USART1_Init 2 */
|
|
|
|
}
|
|
|
|
/* USER CODE BEGIN 1 */
|
|
|
|
/* USER CODE END 1 */
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|