310 lines
30 KiB
C
310 lines
30 KiB
C
#include "rfal_analogConfigTbl.h"
|
|
|
|
const uint8_t rfalAnalogConfigCustomSettings[] = {
|
|
/****** Default Analog Configuration for Chip-Specific Reset ******/
|
|
MODE_ENTRY_16_REG( (RFAL_ANALOG_CONFIG_TECH_CHIP | RFAL_ANALOG_CONFIG_CHIP_INIT)
|
|
, ST25R3916_REG_IO_CONF1, (ST25R3916_REG_IO_CONF1_out_cl_mask | ST25R3916_REG_IO_CONF1_lf_clk_off), 0x07 /* Disable MCU_CLK */
|
|
, ST25R3916_REG_IO_CONF2, (ST25R3916_REG_IO_CONF2_miso_pd1 | ST25R3916_REG_IO_CONF2_miso_pd2 ), 0x18 /* SPI Pull downs */
|
|
// , ST25R3916_REG_IO_CONF2, ST25R3916_REG_IO_CONF2_aat_en, ST25R3916_REG_IO_CONF2_aat_en /* Enable AAT */
|
|
, ST25R3916_REG_TX_DRIVER, ST25R3916_REG_TX_DRIVER_d_res_mask, 0x00 /* Set RFO resistance Active Tx */
|
|
, ST25R3916_REG_RES_AM_MOD, 0xFF, 0x80 /* Use minimum non-overlap */
|
|
, ST25R3916_REG_FIELD_THRESHOLD_ACTV, ST25R3916_REG_FIELD_THRESHOLD_ACTV_trg_mask, ST25R3916_REG_FIELD_THRESHOLD_ACTV_trg_105mV /* Lower activation threshold (higher than deactivation)*/
|
|
, ST25R3916_REG_FIELD_THRESHOLD_ACTV, ST25R3916_REG_FIELD_THRESHOLD_ACTV_rfe_mask, ST25R3916_REG_FIELD_THRESHOLD_ACTV_rfe_105mV /* Lower activation threshold (higher than deactivation)*/
|
|
, ST25R3916_REG_FIELD_THRESHOLD_DEACTV, ST25R3916_REG_FIELD_THRESHOLD_DEACTV_trg_mask, ST25R3916_REG_FIELD_THRESHOLD_DEACTV_trg_75mV /* Lower deactivation threshold */
|
|
, ST25R3916_REG_FIELD_THRESHOLD_DEACTV, ST25R3916_REG_FIELD_THRESHOLD_DEACTV_rfe_mask, ST25R3916_REG_FIELD_THRESHOLD_DEACTV_rfe_75mV /* Lower deactivation threshold */
|
|
, ST25R3916_REG_AUX_MOD, ST25R3916_REG_AUX_MOD_lm_ext, ST25R3916_REG_AUX_MOD_lm_ext /* Disable External Load Modulation */
|
|
, ST25R3916_REG_AUX_MOD, ST25R3916_REG_AUX_MOD_lm_dri, ST25R3916_REG_AUX_MOD_lm_dri /* Use internal Load Modulation */
|
|
, ST25R3916_REG_PASSIVE_TARGET, ST25R3916_REG_PASSIVE_TARGET_fdel_mask, (5U<<ST25R3916_REG_PASSIVE_TARGET_fdel_shift) /* Adjust the FDT to be aligned with the bitgrid */
|
|
, ST25R3916_REG_PT_MOD, (ST25R3916_REG_PT_MOD_ptm_res_mask | ST25R3916_REG_PT_MOD_pt_res_mask), 0x0f /* Reduce RFO resistance in Modulated state */
|
|
, ST25R3916_REG_EMD_SUP_CONF, ST25R3916_REG_EMD_SUP_CONF_rx_start_emv, ST25R3916_REG_EMD_SUP_CONF_rx_start_emv_on /* Enable start on first 4 bits */
|
|
, ST25R3916_REG_ANT_TUNE_A, 0xFF, 0x82 /* Set Antenna Tuning (Poller): ANTL */
|
|
, ST25R3916_REG_ANT_TUNE_B, 0xFF, 0x82 /* Set Antenna Tuning (Poller): ANTL */
|
|
, 0x84U, 0x10, 0x10 /* Avoid chip internal overheat protection */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Chip-Specific Poll Common ******/
|
|
, MODE_ENTRY_9_REG( (RFAL_ANALOG_CONFIG_TECH_CHIP | RFAL_ANALOG_CONFIG_CHIP_POLL_COMMON)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
|
|
, ST25R3916_REG_TX_DRIVER, ST25R3916_REG_TX_DRIVER_am_mod_mask, ST25R3916_REG_TX_DRIVER_am_mod_12percent /* Set Modulation index */
|
|
, ST25R3916_REG_AUX_MOD, (ST25R3916_REG_AUX_MOD_dis_reg_am | ST25R3916_REG_AUX_MOD_res_am), 0x00 /* Use AM via regulator */
|
|
, ST25R3916_REG_ANT_TUNE_A, 0xFF, 0x82 /* Set Antenna Tuning (Poller): ANTL */
|
|
, ST25R3916_REG_ANT_TUNE_B, 0xFF, 0x82 /* Set Antenna Tuning (Poller): ANTL */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x00 /* Disable Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x00 /* Disable Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x00 /* Disable Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x00 /* Disable Undershoot Protection */
|
|
)
|
|
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Rx Common ******/
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_AUX, ST25R3916_REG_AUX_dis_corr, ST25R3916_REG_AUX_dis_corr_correlator /* Use Correlator Receiver */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Tx 106 ******/
|
|
, MODE_ENTRY_5_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am, ST25R3916_REG_MODE_tr_am_ook /* Use OOK */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x40 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x03 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x40 /* Set default Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x03 /* Set default Undershoot Protection */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Rx 106 ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x08
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x2D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x51
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Tx 212 ******/
|
|
, MODE_ENTRY_7_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
|
|
, ST25R3916_REG_AUX_MOD, (ST25R3916_REG_AUX_MOD_dis_reg_am | ST25R3916_REG_AUX_MOD_res_am), 0x88 /* Use Resistive AM */
|
|
, ST25R3916_REG_RES_AM_MOD, ST25R3916_REG_RES_AM_MOD_md_res_mask, 0x7F /* Set Resistive modulation */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x40 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x03 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x40 /* Set default Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x03 /* Set default Undershoot Protection */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Rx 212 ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x02
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x14
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Tx 424 ******/
|
|
, MODE_ENTRY_7_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
|
|
, ST25R3916_REG_AUX_MOD, (ST25R3916_REG_AUX_MOD_dis_reg_am | ST25R3916_REG_AUX_MOD_res_am), 0x88 /* Use Resistive AM */
|
|
, ST25R3916_REG_RES_AM_MOD, ST25R3916_REG_RES_AM_MOD_md_res_mask, 0x7F /* Set Resistive modulation */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x40 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x03 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x40 /* Set default Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x03 /* Set default Undershoot Protection */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Rx 424 ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x42
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x54
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Tx 848 ******/
|
|
, MODE_ENTRY_7_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_848 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
|
|
, ST25R3916_REG_TX_DRIVER, ST25R3916_REG_TX_DRIVER_am_mod_mask, ST25R3916_REG_TX_DRIVER_am_mod_40percent /* Set Modulation index */
|
|
, ST25R3916_REG_AUX_MOD, (ST25R3916_REG_AUX_MOD_dis_reg_am | ST25R3916_REG_AUX_MOD_res_am), 0x00 /* Use AM via regulator */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x00 /* Disable Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x00 /* Disable Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x00 /* Disable Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x00 /* Disable Undershoot Protection */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Rx 848 ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_848 | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x42
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x44
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-A Anticolision setting ******/
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_ANTICOL)
|
|
, ST25R3916_REG_CORR_CONF1, ST25R3916_REG_CORR_CONF1_corr_s6, 0x00 /* Set collision detection level different from data */
|
|
)
|
|
|
|
#ifdef RFAL_USE_COHE
|
|
/****** Default Analog Configuration for Poll NFC-B Rx Common ******/
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_AUX, ST25R3916_REG_AUX_dis_corr, ST25R3916_REG_AUX_dis_corr_coherent /* Use Coherent Receiver */
|
|
)
|
|
#else
|
|
/****** Default Analog Configuration for Poll NFC-B Rx Common ******/
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_AUX, ST25R3916_REG_AUX_dis_corr, ST25R3916_REG_AUX_dis_corr_correlator /* Use Correlator Receiver */
|
|
)
|
|
#endif /*RFAL_USE_COHE*/
|
|
|
|
/****** Default Analog Configuration for Poll NFC-B Rx 106 ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x04
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x1B
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-B Rx 212 ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x02
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x14
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-B Rx 424 ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x42
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x54
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll NFC-B Rx 848 ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_848 | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x42
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x44
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
#ifdef RFAL_USE_COHE
|
|
|
|
/****** Default Analog Configuration for Poll NFC-F Rx Common ******/
|
|
, MODE_ENTRY_7_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCF | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_AUX, ST25R3916_REG_AUX_dis_corr, ST25R3916_REG_AUX_dis_corr_coherent /* Use Pulse Receiver */
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x13
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x54
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
#else
|
|
/****** Default Analog Configuration for Poll NFC-F Rx Common ******/
|
|
, MODE_ENTRY_7_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCF | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_AUX, ST25R3916_REG_AUX_dis_corr, ST25R3916_REG_AUX_dis_corr_correlator /* Use Correlator Receiver */
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x13
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x3D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x54
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x00
|
|
)
|
|
#endif /*RFAL_USE_COHE*/
|
|
|
|
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCV | RFAL_ANALOG_CONFIG_BITRATE_1OF4 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am, ST25R3916_REG_MODE_tr_am_ook /* Use OOK */
|
|
)
|
|
|
|
|
|
#ifdef RFAL_USE_COHE
|
|
/****** Default Analog Configuration for Poll NFC-V Rx Common ******/
|
|
, MODE_ENTRY_7_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCV | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_AUX, ST25R3916_REG_AUX_dis_corr, ST25R3916_REG_AUX_dis_corr_coherent /* Use Pulse Receiver */
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x13
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x2D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x13
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x01
|
|
)
|
|
#else
|
|
/****** Default Analog Configuration for Poll NFC-V Rx Common ******/
|
|
, MODE_ENTRY_7_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCV | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_AUX, ST25R3916_REG_AUX_dis_corr, ST25R3916_REG_AUX_dis_corr_correlator /* Use Correlator Receiver */
|
|
, ST25R3916_REG_RX_CONF1, 0xFF, 0x13
|
|
, ST25R3916_REG_RX_CONF2, 0xFF, 0x2D
|
|
, ST25R3916_REG_RX_CONF3, 0xFF, 0x00
|
|
, ST25R3916_REG_RX_CONF4, 0xFF, 0x00
|
|
, ST25R3916_REG_CORR_CONF1, 0xFF, 0x13
|
|
, ST25R3916_REG_CORR_CONF2, 0xFF, 0x01
|
|
)
|
|
#endif /*RFAL_USE_COHE*/
|
|
|
|
|
|
/****** Default Analog Configuration for Poll AP2P Tx 106 ******/
|
|
, MODE_ENTRY_5_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_ook /* Use OOK modulation */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x40 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x03 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x40 /* Set default Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x03 /* Set default Undershoot Protection */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll AP2P Tx 212 ******/
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Poll AP2P Tx 424 ******/
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
|
|
)
|
|
|
|
|
|
/****** Default Analog Configuration for Chip-Specific Listen On ******/
|
|
, MODE_ENTRY_6_REG( (RFAL_ANALOG_CONFIG_TECH_CHIP | RFAL_ANALOG_CONFIG_CHIP_LISTEN_ON)
|
|
, ST25R3916_REG_ANT_TUNE_A, 0xFF, 0x00 /* Set Antenna Tuning (Listener): ANTL */
|
|
, ST25R3916_REG_ANT_TUNE_B, 0xFF, 0xff /* Set Antenna Tuning (Listener): ANTL */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x00 /* Disable Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x00 /* Disable Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x00 /* Disable Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x00 /* Disable Undershoot Protection */
|
|
)
|
|
|
|
|
|
/****** Default Analog Configuration for Listen AP2P Tx Common ******/
|
|
, MODE_ENTRY_7_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_ANT_TUNE_A, 0xFF, 0x82 /* Set Antenna Tuning (Poller): ANTL */
|
|
, ST25R3916_REG_ANT_TUNE_B, 0xFF, 0x82 /* Set Antenna Tuning (Poller): ANTL */
|
|
, ST25R3916_REG_TX_DRIVER, ST25R3916_REG_TX_DRIVER_am_mod_mask, ST25R3916_REG_TX_DRIVER_am_mod_12percent /* Set Modulation index */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x00 /* Disable Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x00 /* Disable Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x00 /* Disable Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x00 /* Disable Undershoot Protection */
|
|
)
|
|
|
|
|
|
/****** Default Analog Configuration for Listen AP2P Rx Common ******/
|
|
, MODE_ENTRY_3_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
|
|
, ST25R3916_REG_RX_CONF1, ST25R3916_REG_RX_CONF1_lp_mask, ST25R3916_REG_RX_CONF1_lp_1200khz /* Set Rx filter configuration */
|
|
, ST25R3916_REG_RX_CONF1, ST25R3916_REG_RX_CONF1_hz_mask, ST25R3916_REG_RX_CONF1_hz_12_200khz /* Set Rx filter configuration */
|
|
, ST25R3916_REG_RX_CONF2, ST25R3916_REG_RX_CONF2_amd_sel, ST25R3916_REG_RX_CONF2_amd_sel_mixer /* AM demodulator: mixer */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Listen AP2P Tx 106 ******/
|
|
, MODE_ENTRY_5_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_ook /* Use OOK modulation */
|
|
, ST25R3916_REG_OVERSHOOT_CONF1, 0xFF, 0x40 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_OVERSHOOT_CONF2, 0xFF, 0x03 /* Set default Overshoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF1, 0xFF, 0x40 /* Set default Undershoot Protection */
|
|
, ST25R3916_REG_UNDERSHOOT_CONF2, 0xFF, 0x03 /* Set default Undershoot Protection */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Listen AP2P Tx 212 ******/
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
|
|
)
|
|
|
|
/****** Default Analog Configuration for Listen AP2P Tx 424 ******/
|
|
, MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_TX)
|
|
, ST25R3916_REG_MODE, ST25R3916_REG_MODE_tr_am , ST25R3916_REG_MODE_tr_am_am /* Use AM modulation */
|
|
)
|
|
|
|
};
|
|
|
|
const uint16_t rfalAnalogConfigCustomSettingsLength = sizeof(rfalAnalogConfigCustomSettings);
|