0c7a38b99f
* Switch to smaller radio stack. BleGlue: update params to match new stack. Update scripts * Git: set eol to lf
454 lines
15 KiB
C
454 lines
15 KiB
C
#pragma once
|
|
|
|
#include "hw.h"
|
|
#include "hw_conf.h"
|
|
#include "hw_if.h"
|
|
#include "ble_bufsize.h"
|
|
|
|
#define CFG_TX_POWER (0x19) /* +0dBm */
|
|
|
|
/**
|
|
* Define Advertising parameters
|
|
*/
|
|
#define CFG_ADV_BD_ADDRESS (0x7257acd87a6c)
|
|
#define CFG_FAST_CONN_ADV_INTERVAL_MIN (0x80) /**< 80ms */
|
|
#define CFG_FAST_CONN_ADV_INTERVAL_MAX (0xa0) /**< 100ms */
|
|
#define CFG_LP_CONN_ADV_INTERVAL_MIN (0x640) /**< 1s */
|
|
#define CFG_LP_CONN_ADV_INTERVAL_MAX (0xfa0) /**< 2.5s */
|
|
|
|
/**
|
|
* Define IO Authentication
|
|
*/
|
|
#define CFG_BONDING_MODE (1)
|
|
#define CFG_FIXED_PIN (111111)
|
|
#define CFG_USED_FIXED_PIN (1)
|
|
#define CFG_ENCRYPTION_KEY_SIZE_MAX (16)
|
|
#define CFG_ENCRYPTION_KEY_SIZE_MIN (8)
|
|
|
|
/**
|
|
* Define IO capabilities
|
|
*/
|
|
#define CFG_IO_CAPABILITY_DISPLAY_ONLY (0x00)
|
|
#define CFG_IO_CAPABILITY_DISPLAY_YES_NO (0x01)
|
|
#define CFG_IO_CAPABILITY_KEYBOARD_ONLY (0x02)
|
|
#define CFG_IO_CAPABILITY_NO_INPUT_NO_OUTPUT (0x03)
|
|
#define CFG_IO_CAPABILITY_KEYBOARD_DISPLAY (0x04)
|
|
|
|
#define CFG_IO_CAPABILITY CFG_IO_CAPABILITY_DISPLAY_YES_NO
|
|
|
|
/**
|
|
* Define MITM modes
|
|
*/
|
|
#define CFG_MITM_PROTECTION_NOT_REQUIRED (0x00)
|
|
#define CFG_MITM_PROTECTION_REQUIRED (0x01)
|
|
|
|
#define CFG_MITM_PROTECTION CFG_MITM_PROTECTION_REQUIRED
|
|
|
|
/**
|
|
* Define Secure Connections Support
|
|
*/
|
|
#define CFG_SECURE_NOT_SUPPORTED (0x00)
|
|
#define CFG_SECURE_OPTIONAL (0x01)
|
|
#define CFG_SECURE_MANDATORY (0x02)
|
|
|
|
#define CFG_SC_SUPPORT CFG_SECURE_OPTIONAL
|
|
|
|
/**
|
|
* Define Keypress Notification Support
|
|
*/
|
|
#define CFG_KEYPRESS_NOT_SUPPORTED (0x00)
|
|
#define CFG_KEYPRESS_SUPPORTED (0x01)
|
|
|
|
#define CFG_KEYPRESS_NOTIFICATION_SUPPORT CFG_KEYPRESS_NOT_SUPPORTED
|
|
|
|
/**
|
|
* Numeric Comparison Answers
|
|
*/
|
|
#define YES (0x01)
|
|
#define NO (0x00)
|
|
|
|
/**
|
|
* Device name configuration for Generic Access Service
|
|
*/
|
|
#define CFG_GAP_DEVICE_NAME "TEMPLATE"
|
|
#define CFG_GAP_DEVICE_NAME_LENGTH (8)
|
|
|
|
/**
|
|
* Define PHY
|
|
*/
|
|
#define ALL_PHYS_PREFERENCE 0x00
|
|
#define RX_2M_PREFERRED 0x02
|
|
#define TX_2M_PREFERRED 0x02
|
|
#define TX_1M 0x01
|
|
#define TX_2M 0x02
|
|
#define RX_1M 0x01
|
|
#define RX_2M 0x02
|
|
|
|
/**
|
|
* Identity root key used to derive LTK and CSRK
|
|
*/
|
|
#define CFG_BLE_IRK {0x12,0x34,0x56,0x78,0x9a,0xbc,0xde,0xf0,0x12,0x34,0x56,0x78,0x9a,0xbc,0xde,0xf0}
|
|
|
|
/**
|
|
* Encryption root key used to derive LTK and CSRK
|
|
*/
|
|
#define CFG_BLE_ERK {0xfe,0xdc,0xba,0x09,0x87,0x65,0x43,0x21,0xfe,0xdc,0xba,0x09,0x87,0x65,0x43,0x21}
|
|
|
|
/* USER CODE BEGIN Generic_Parameters */
|
|
/**
|
|
* SMPS supply
|
|
* SMPS not used when Set to 0
|
|
* SMPS used when Set to 1
|
|
*/
|
|
#define CFG_USE_SMPS 1
|
|
/* USER CODE END Generic_Parameters */
|
|
|
|
/**< specific parameters */
|
|
/*****************************************************/
|
|
|
|
/**
|
|
* AD Element - Group B Feature
|
|
*/
|
|
/* LSB - Second Byte */
|
|
#define CFG_FEATURE_OTA_REBOOT (0x20)
|
|
|
|
/******************************************************************************
|
|
* BLE Stack
|
|
******************************************************************************/
|
|
/**
|
|
* Maximum number of simultaneous connections that the device will support.
|
|
* Valid values are from 1 to 8
|
|
*/
|
|
#define CFG_BLE_NUM_LINK 2
|
|
|
|
/**
|
|
* Maximum number of Services that can be stored in the GATT database.
|
|
* Note that the GAP and GATT services are automatically added so this parameter should be 2 plus the number of user services
|
|
*/
|
|
#define CFG_BLE_NUM_GATT_SERVICES 8
|
|
|
|
/**
|
|
* Maximum number of Attributes
|
|
* (i.e. the number of characteristic + the number of characteristic values + the number of descriptors, excluding the services)
|
|
* that can be stored in the GATT database.
|
|
* Note that certain characteristics and relative descriptors are added automatically during device initialization
|
|
* so this parameters should be 9 plus the number of user Attributes
|
|
*/
|
|
#define CFG_BLE_NUM_GATT_ATTRIBUTES 68
|
|
|
|
/**
|
|
* Maximum supported ATT_MTU size
|
|
*/
|
|
#define CFG_BLE_MAX_ATT_MTU (256+128+16+8+4+2)
|
|
|
|
/**
|
|
* Size of the storage area for Attribute values
|
|
* This value depends on the number of attributes used by application. In particular the sum of the following quantities (in octets) should be made for each attribute:
|
|
* - attribute value length
|
|
* - 5, if UUID is 16 bit; 19, if UUID is 128 bit
|
|
* - 2, if server configuration descriptor is used
|
|
* - 2*DTM_NUM_LINK, if client configuration descriptor is used
|
|
* - 2, if extended properties is used
|
|
* The total amount of memory needed is the sum of the above quantities for each attribute.
|
|
*/
|
|
#define CFG_BLE_ATT_VALUE_ARRAY_SIZE (1344)
|
|
|
|
/**
|
|
* Prepare Write List size in terms of number of packet
|
|
*/
|
|
#define CFG_BLE_PREPARE_WRITE_LIST_SIZE BLE_PREP_WRITE_X_ATT(CFG_BLE_MAX_ATT_MTU)
|
|
|
|
/**
|
|
* Number of allocated memory blocks
|
|
*/
|
|
#define CFG_BLE_MBLOCK_COUNT (BLE_MBLOCKS_CALC(CFG_BLE_PREPARE_WRITE_LIST_SIZE, CFG_BLE_MAX_ATT_MTU, CFG_BLE_NUM_LINK))
|
|
|
|
/**
|
|
* Enable or disable the Extended Packet length feature. Valid values are 0 or 1.
|
|
*/
|
|
#define CFG_BLE_DATA_LENGTH_EXTENSION 1
|
|
|
|
/**
|
|
* Sleep clock accuracy in Slave mode (ppm value)
|
|
*/
|
|
#define CFG_BLE_SLAVE_SCA 500
|
|
|
|
/**
|
|
* Sleep clock accuracy in Master mode
|
|
* 0 : 251 ppm to 500 ppm
|
|
* 1 : 151 ppm to 250 ppm
|
|
* 2 : 101 ppm to 150 ppm
|
|
* 3 : 76 ppm to 100 ppm
|
|
* 4 : 51 ppm to 75 ppm
|
|
* 5 : 31 ppm to 50 ppm
|
|
* 6 : 21 ppm to 30 ppm
|
|
* 7 : 0 ppm to 20 ppm
|
|
*/
|
|
#define CFG_BLE_MASTER_SCA 0
|
|
|
|
/**
|
|
* Source for the low speed clock for RF wake-up
|
|
* 1 : external high speed crystal HSE/32/32
|
|
* 0 : external low speed crystal ( no calibration )
|
|
*/
|
|
#define CFG_BLE_LSE_SOURCE 0
|
|
|
|
/**
|
|
* Start up time of the high speed (16 or 32 MHz) crystal oscillator in units of 625/256 us (~2.44 us)
|
|
*/
|
|
#define CFG_BLE_HSE_STARTUP_TIME 0x148
|
|
|
|
/**
|
|
* Maximum duration of the connection event when the device is in Slave mode in units of 625/256 us (~2.44 us)
|
|
*/
|
|
#define CFG_BLE_MAX_CONN_EVENT_LENGTH ( 0xFFFFFFFF )
|
|
|
|
/**
|
|
* Viterbi Mode
|
|
* 1 : enabled
|
|
* 0 : disabled
|
|
*/
|
|
#define CFG_BLE_VITERBI_MODE 1
|
|
|
|
/**
|
|
* BLE stack Options flags to be configured with:
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_LL_ONLY
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_LL_HOST
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_NO_SVC_CHANGE_DESC
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_WITH_SVC_CHANGE_DESC
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_DEVICE_NAME_RO
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_DEVICE_NAME_RW
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_EXT_ADV
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_NO_EXT_ADV
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_CS_ALGO2
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_NO_CS_ALGO2
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_POWER_CLASS_1
|
|
* - SHCI_C2_BLE_INIT_OPTIONS_POWER_CLASS_2_3
|
|
* which are used to set following configuration bits:
|
|
* (bit 0): 1: LL only
|
|
* 0: LL + host
|
|
* (bit 1): 1: no service change desc.
|
|
* 0: with service change desc.
|
|
* (bit 2): 1: device name Read-Only
|
|
* 0: device name R/W
|
|
* (bit 3): 1: extended advertizing supported [NOT SUPPORTED]
|
|
* 0: extended advertizing not supported [NOT SUPPORTED]
|
|
* (bit 4): 1: CS Algo #2 supported
|
|
* 0: CS Algo #2 not supported
|
|
* (bit 7): 1: LE Power Class 1
|
|
* 0: LE Power Class 2-3
|
|
* other bits: reserved (shall be set to 0)
|
|
*/
|
|
#define CFG_BLE_OPTIONS (SHCI_C2_BLE_INIT_OPTIONS_LL_HOST | SHCI_C2_BLE_INIT_OPTIONS_WITH_SVC_CHANGE_DESC | SHCI_C2_BLE_INIT_OPTIONS_DEVICE_NAME_RW | SHCI_C2_BLE_INIT_OPTIONS_NO_EXT_ADV | SHCI_C2_BLE_INIT_OPTIONS_NO_CS_ALGO2 | SHCI_C2_BLE_INIT_OPTIONS_POWER_CLASS_2_3)
|
|
|
|
/**
|
|
* Queue length of BLE Event
|
|
* This parameter defines the number of asynchronous events that can be stored in the HCI layer before
|
|
* being reported to the application. When a command is sent to the BLE core coprocessor, the HCI layer
|
|
* is waiting for the event with the Num_HCI_Command_Packets set to 1. The receive queue shall be large
|
|
* enough to store all asynchronous events received in between.
|
|
* When CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE is set to 27, this allow to store three 255 bytes long asynchronous events
|
|
* between the HCI command and its event.
|
|
* This parameter depends on the value given to CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE. When the queue size is to small,
|
|
* the system may hang if the queue is full with asynchronous events and the HCI layer is still waiting
|
|
* for a CC/CS event, In that case, the notification TL_BLE_HCI_ToNot() is called to indicate
|
|
* to the application a HCI command did not receive its command event within 30s (Default HCI Timeout).
|
|
*/
|
|
#define CFG_TLBLE_EVT_QUEUE_LENGTH 5
|
|
/**
|
|
* This parameter should be set to fit most events received by the HCI layer. It defines the buffer size of each element
|
|
* allocated in the queue of received events and can be used to optimize the amount of RAM allocated by the Memory Manager.
|
|
* It should not exceed 255 which is the maximum HCI packet payload size (a greater value is a lost of memory as it will
|
|
* never be used)
|
|
* With the current wireless firmware implementation, this parameter shall be kept to 255
|
|
*
|
|
*/
|
|
#define CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE 255 /**< Set to 255 with the memory manager and the mailbox */
|
|
|
|
#define TL_BLE_EVENT_FRAME_SIZE ( TL_EVT_HDR_SIZE + CFG_TLBLE_MOST_EVENT_PAYLOAD_SIZE )
|
|
/******************************************************************************
|
|
* UART interfaces
|
|
******************************************************************************/
|
|
|
|
/**
|
|
* Select UART interfaces
|
|
*/
|
|
#define CFG_DEBUG_TRACE_UART hw_uart1
|
|
#define CFG_CONSOLE_MENU 0
|
|
|
|
/******************************************************************************
|
|
* Low Power
|
|
******************************************************************************/
|
|
/**
|
|
* When set to 1, the low power mode is enable
|
|
* When set to 0, the device stays in RUN mode
|
|
*/
|
|
#define CFG_LPM_SUPPORTED 1
|
|
|
|
/******************************************************************************
|
|
* Timer Server
|
|
******************************************************************************/
|
|
/**
|
|
* CFG_RTC_WUCKSEL_DIVIDER: This sets the RTCCLK divider to the wakeup timer.
|
|
* The lower is the value, the better is the power consumption and the accuracy of the timerserver
|
|
* The higher is the value, the finest is the granularity
|
|
*
|
|
* CFG_RTC_ASYNCH_PRESCALER: This sets the asynchronous prescaler of the RTC. It should as high as possible ( to ouput
|
|
* clock as low as possible) but the output clock should be equal or higher frequency compare to the clock feeding
|
|
* the wakeup timer. A lower clock speed would impact the accuracy of the timer server.
|
|
*
|
|
* CFG_RTC_SYNCH_PRESCALER: This sets the synchronous prescaler of the RTC.
|
|
* When the 1Hz calendar clock is required, it shall be sets according to other settings
|
|
* When the 1Hz calendar clock is not needed, CFG_RTC_SYNCH_PRESCALER should be set to 0x7FFF (MAX VALUE)
|
|
*
|
|
* CFG_RTCCLK_DIVIDER_CONF:
|
|
* Shall be set to either 0,2,4,8,16
|
|
* When set to either 2,4,8,16, the 1Hhz calendar is supported
|
|
* When set to 0, the user sets its own configuration
|
|
*
|
|
* The following settings are computed with LSI as input to the RTC
|
|
*/
|
|
#define CFG_RTCCLK_DIVIDER_CONF 0
|
|
|
|
#if (CFG_RTCCLK_DIVIDER_CONF == 0)
|
|
/**
|
|
* Custom configuration
|
|
* It does not support 1Hz calendar
|
|
* It divides the RTC CLK by 16
|
|
*/
|
|
#define CFG_RTCCLK_DIV (16)
|
|
#define CFG_RTC_WUCKSEL_DIVIDER (0)
|
|
#define CFG_RTC_ASYNCH_PRESCALER (CFG_RTCCLK_DIV - 1)
|
|
#define CFG_RTC_SYNCH_PRESCALER (0x7FFF)
|
|
|
|
#else
|
|
|
|
#if (CFG_RTCCLK_DIVIDER_CONF == 2)
|
|
/**
|
|
* It divides the RTC CLK by 2
|
|
*/
|
|
#define CFG_RTC_WUCKSEL_DIVIDER (3)
|
|
#endif
|
|
|
|
#if (CFG_RTCCLK_DIVIDER_CONF == 4)
|
|
/**
|
|
* It divides the RTC CLK by 4
|
|
*/
|
|
#define CFG_RTC_WUCKSEL_DIVIDER (2)
|
|
#endif
|
|
|
|
#if (CFG_RTCCLK_DIVIDER_CONF == 8)
|
|
/**
|
|
* It divides the RTC CLK by 8
|
|
*/
|
|
#define CFG_RTC_WUCKSEL_DIVIDER (1)
|
|
#endif
|
|
|
|
#if (CFG_RTCCLK_DIVIDER_CONF == 16)
|
|
/**
|
|
* It divides the RTC CLK by 16
|
|
*/
|
|
#define CFG_RTC_WUCKSEL_DIVIDER (0)
|
|
#endif
|
|
|
|
#define CFG_RTCCLK_DIV CFG_RTCCLK_DIVIDER_CONF
|
|
#define CFG_RTC_ASYNCH_PRESCALER (CFG_RTCCLK_DIV - 1)
|
|
#define CFG_RTC_SYNCH_PRESCALER (DIVR( LSE_VALUE, (CFG_RTC_ASYNCH_PRESCALER+1) ) - 1 )
|
|
|
|
#endif
|
|
|
|
/** tick timer value in us */
|
|
#define CFG_TS_TICK_VAL DIVR( (CFG_RTCCLK_DIV * 1000000), LSE_VALUE )
|
|
|
|
typedef enum
|
|
{
|
|
CFG_TIM_PROC_ID_ISR,
|
|
/* USER CODE BEGIN CFG_TimProcID_t */
|
|
|
|
/* USER CODE END CFG_TimProcID_t */
|
|
} CFG_TimProcID_t;
|
|
|
|
/******************************************************************************
|
|
* Debug
|
|
******************************************************************************/
|
|
/**
|
|
* When set, this resets some hw resources to set the device in the same state than the power up
|
|
* The FW resets only register that may prevent the FW to run properly
|
|
*
|
|
* This shall be set to 0 in a final product
|
|
*
|
|
*/
|
|
#define CFG_HW_RESET_BY_FW 0
|
|
|
|
/**
|
|
* keep debugger enabled while in any low power mode when set to 1
|
|
* should be set to 0 in production
|
|
*/
|
|
#define CFG_DEBUGGER_SUPPORTED 0
|
|
|
|
/**
|
|
* When set to 1, the traces are enabled in the BLE services
|
|
*/
|
|
#define CFG_DEBUG_BLE_TRACE 0
|
|
|
|
/**
|
|
* Enable or Disable traces in application
|
|
*/
|
|
#define CFG_DEBUG_APP_TRACE 0
|
|
|
|
#if (CFG_DEBUG_APP_TRACE != 0)
|
|
#define APP_DBG_MSG PRINT_MESG_DBG
|
|
#else
|
|
#define APP_DBG_MSG PRINT_NO_MESG
|
|
#endif
|
|
|
|
#if ( (CFG_DEBUG_BLE_TRACE != 0) || (CFG_DEBUG_APP_TRACE != 0) )
|
|
#define CFG_DEBUG_TRACE 1
|
|
#endif
|
|
|
|
#if (CFG_DEBUG_TRACE != 0)
|
|
#undef CFG_LPM_SUPPORTED
|
|
#undef CFG_DEBUGGER_SUPPORTED
|
|
#define CFG_LPM_SUPPORTED 0
|
|
#define CFG_DEBUGGER_SUPPORTED 1
|
|
#endif
|
|
|
|
/**
|
|
* When CFG_DEBUG_TRACE_FULL is set to 1, the trace are output with the API name, the file name and the line number
|
|
* When CFG_DEBUG_TRACE_LIGHT is set to 1, only the debug message is output
|
|
*
|
|
* When both are set to 0, no trace are output
|
|
* When both are set to 1, CFG_DEBUG_TRACE_FULL is selected
|
|
*/
|
|
#define CFG_DEBUG_TRACE_LIGHT 0
|
|
#define CFG_DEBUG_TRACE_FULL 0
|
|
|
|
#if (( CFG_DEBUG_TRACE != 0 ) && ( CFG_DEBUG_TRACE_LIGHT == 0 ) && (CFG_DEBUG_TRACE_FULL == 0))
|
|
#undef CFG_DEBUG_TRACE_FULL
|
|
#undef CFG_DEBUG_TRACE_LIGHT
|
|
#define CFG_DEBUG_TRACE_FULL 0
|
|
#define CFG_DEBUG_TRACE_LIGHT 1
|
|
#endif
|
|
|
|
#if ( CFG_DEBUG_TRACE == 0 )
|
|
#undef CFG_DEBUG_TRACE_FULL
|
|
#undef CFG_DEBUG_TRACE_LIGHT
|
|
#define CFG_DEBUG_TRACE_FULL 0
|
|
#define CFG_DEBUG_TRACE_LIGHT 0
|
|
#endif
|
|
|
|
/**
|
|
* When not set, the traces is looping on sending the trace over UART
|
|
*/
|
|
#define DBG_TRACE_USE_CIRCULAR_QUEUE 0
|
|
|
|
/**
|
|
* max buffer Size to queue data traces and max data trace allowed.
|
|
* Only Used if DBG_TRACE_USE_CIRCULAR_QUEUE is defined
|
|
*/
|
|
#define DBG_TRACE_MSG_QUEUE_SIZE 4096
|
|
#define MAX_DBG_TRACE_MSG_SIZE 1024
|
|
|
|
#define CFG_OTP_BASE_ADDRESS OTP_AREA_BASE
|
|
#define CFG_OTP_END_ADRESS OTP_AREA_END_ADDR
|