223 lines
8.4 KiB
C
223 lines
8.4 KiB
C
#include "u8g2_glue.h"
|
|
|
|
#include <furi-hal.h>
|
|
|
|
static FuriHalSpiDevice* u8g2_periphery_display = NULL;
|
|
|
|
uint8_t u8g2_gpio_and_delay_stm32(u8x8_t* u8x8, uint8_t msg, uint8_t arg_int, void* arg_ptr) {
|
|
switch(msg) {
|
|
case U8X8_MSG_GPIO_AND_DELAY_INIT:
|
|
/* HAL initialization contains all what we need so we can skip this part. */
|
|
break;
|
|
case U8X8_MSG_DELAY_MILLI:
|
|
delay(arg_int);
|
|
break;
|
|
case U8X8_MSG_DELAY_10MICRO:
|
|
delay_us(10);
|
|
break;
|
|
case U8X8_MSG_DELAY_100NANO:
|
|
asm("nop");
|
|
break;
|
|
case U8X8_MSG_GPIO_RESET:
|
|
hal_gpio_write(&gpio_display_rst, arg_int);
|
|
break;
|
|
default:
|
|
return 0;
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
|
|
uint8_t u8x8_hw_spi_stm32(u8x8_t* u8x8, uint8_t msg, uint8_t arg_int, void* arg_ptr) {
|
|
switch(msg) {
|
|
case U8X8_MSG_BYTE_SEND:
|
|
furi_hal_spi_bus_tx(u8g2_periphery_display->bus, (uint8_t*)arg_ptr, arg_int, 10000);
|
|
break;
|
|
case U8X8_MSG_BYTE_SET_DC:
|
|
hal_gpio_write(&gpio_display_di, arg_int);
|
|
break;
|
|
case U8X8_MSG_BYTE_INIT:
|
|
break;
|
|
case U8X8_MSG_BYTE_START_TRANSFER:
|
|
furi_assert(u8g2_periphery_display == NULL);
|
|
u8g2_periphery_display =
|
|
(FuriHalSpiDevice*)furi_hal_spi_device_get(FuriHalSpiDeviceIdDisplay);
|
|
hal_gpio_write(u8g2_periphery_display->chip_select, false);
|
|
break;
|
|
case U8X8_MSG_BYTE_END_TRANSFER:
|
|
furi_assert(u8g2_periphery_display);
|
|
hal_gpio_write(u8g2_periphery_display->chip_select, true);
|
|
furi_hal_spi_device_return(u8g2_periphery_display);
|
|
u8g2_periphery_display = NULL;
|
|
break;
|
|
default:
|
|
return 0;
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
|
|
static const uint8_t u8x8_d_st7565_powersave0_seq[] = {
|
|
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
|
|
U8X8_C(0x0a4), /* all pixel off, issue 142 */
|
|
U8X8_C(0x0af), /* display on */
|
|
U8X8_END_TRANSFER(), /* disable chip */
|
|
U8X8_END() /* end of sequence */
|
|
};
|
|
|
|
static const uint8_t u8x8_d_st7565_powersave1_seq[] = {
|
|
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
|
|
U8X8_C(0x0ae), /* display off */
|
|
U8X8_C(0x0a5), /* enter powersafe: all pixel on, issue 142 */
|
|
U8X8_END_TRANSFER(), /* disable chip */
|
|
U8X8_END() /* end of sequence */
|
|
};
|
|
|
|
static const uint8_t u8x8_d_st7565_flip0_seq[] = {
|
|
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
|
|
U8X8_C(0x0a1), /* segment remap a0/a1*/
|
|
U8X8_C(0x0c0), /* c0: scan dir normal, c8: reverse */
|
|
U8X8_END_TRANSFER(), /* disable chip */
|
|
U8X8_END() /* end of sequence */
|
|
};
|
|
|
|
static const uint8_t u8x8_d_st7565_flip1_seq[] = {
|
|
U8X8_START_TRANSFER(), /* enable chip, delay is part of the transfer start */
|
|
U8X8_C(0x0a0), /* segment remap a0/a1*/
|
|
U8X8_C(0x0c8), /* c0: scan dir normal, c8: reverse */
|
|
U8X8_END_TRANSFER(), /* disable chip */
|
|
U8X8_END() /* end of sequence */
|
|
};
|
|
|
|
static const u8x8_display_info_t u8x8_st756x_128x64_display_info = {
|
|
.chip_enable_level = 0,
|
|
.chip_disable_level = 1,
|
|
.post_chip_enable_wait_ns = 150, /* st7565 datasheet, table 26, tcsh */
|
|
.pre_chip_disable_wait_ns = 50, /* st7565 datasheet, table 26, tcss */
|
|
.reset_pulse_width_ms = 1,
|
|
.post_reset_wait_ms = 1,
|
|
.sda_setup_time_ns = 50, /* st7565 datasheet, table 26, tsds */
|
|
.sck_pulse_width_ns = 120, /* half of cycle time (100ns according to datasheet), AVR: below 70: 8 MHz, >= 70 --> 4MHz clock */
|
|
.sck_clock_hz = 4000000UL, /* since Arduino 1.6.0, the SPI bus speed in Hz. Should be 1000000000/sck_pulse_width_ns */
|
|
.spi_mode = 0, /* active high, rising edge */
|
|
.i2c_bus_clock_100kHz = 4,
|
|
.data_setup_time_ns = 40, /* st7565 datasheet, table 24, tds8 */
|
|
.write_pulse_width_ns = 80, /* st7565 datasheet, table 24, tcclw */
|
|
.tile_width = 16, /* width of 16*8=128 pixel */
|
|
.tile_height = 8,
|
|
.default_x_offset = 0,
|
|
.flipmode_x_offset = 4,
|
|
.pixel_width = 128,
|
|
.pixel_height = 64
|
|
};
|
|
|
|
uint8_t u8x8_d_st7565_common(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr) {
|
|
uint8_t x, c;
|
|
uint8_t *ptr;
|
|
|
|
switch(msg) {
|
|
case U8X8_MSG_DISPLAY_DRAW_TILE:
|
|
u8x8_cad_StartTransfer(u8x8);
|
|
|
|
x = ((u8x8_tile_t *)arg_ptr)->x_pos;
|
|
x *= 8;
|
|
x += u8x8->x_offset;
|
|
u8x8_cad_SendCmd(u8x8, 0x010 | (x>>4) );
|
|
u8x8_cad_SendCmd(u8x8, 0x000 | ((x&15)));
|
|
u8x8_cad_SendCmd(u8x8, 0x0b0 | (((u8x8_tile_t *)arg_ptr)->y_pos));
|
|
|
|
c = ((u8x8_tile_t *)arg_ptr)->cnt;
|
|
c *= 8;
|
|
ptr = ((u8x8_tile_t *)arg_ptr)->tile_ptr;
|
|
/*
|
|
The following if condition checks the hardware limits of the st7565
|
|
controller: It is not allowed to write beyond the display limits.
|
|
This is in fact an issue within flip mode.
|
|
*/
|
|
if ( c + x > 132u ) {
|
|
c = 132u;
|
|
c -= x;
|
|
}
|
|
|
|
do {
|
|
u8x8_cad_SendData(u8x8, c, ptr); /* note: SendData can not handle more than 255 bytes */
|
|
arg_int--;
|
|
} while( arg_int > 0 );
|
|
|
|
u8x8_cad_EndTransfer(u8x8);
|
|
break;
|
|
case U8X8_MSG_DISPLAY_SET_POWER_SAVE:
|
|
if ( arg_int == 0 )
|
|
u8x8_cad_SendSequence(u8x8, u8x8_d_st7565_powersave0_seq);
|
|
else
|
|
u8x8_cad_SendSequence(u8x8, u8x8_d_st7565_powersave1_seq);
|
|
break;
|
|
#ifdef U8X8_WITH_SET_CONTRAST
|
|
case U8X8_MSG_DISPLAY_SET_CONTRAST:
|
|
u8x8_cad_StartTransfer(u8x8);
|
|
u8x8_cad_SendCmd(u8x8, 0x081 );
|
|
u8x8_cad_SendArg(u8x8, arg_int >> 2 ); /* st7565 has range from 0 to 63 */
|
|
u8x8_cad_EndTransfer(u8x8);
|
|
break;
|
|
#endif
|
|
default:
|
|
return 0;
|
|
}
|
|
return 1;
|
|
}
|
|
|
|
static const uint8_t u8x8_d_st756x_erc_init_seq[] = {
|
|
U8X8_START_TRANSFER(),
|
|
U8X8_C(0x0e2), // soft reset
|
|
U8X8_C(0xA3), // CMD_SET_BIAS_7
|
|
U8X8_C(0xA0), // CMD_SET_ADC_NORMAL
|
|
U8X8_C(0xC8), // CMD_SET_COM_REVERSE
|
|
U8X8_C(0x40), // CMD_SET_DISP_START_LINE
|
|
U8X8_C(0x28 | 0x4), // CMD_SET_POWER_CONTROL | 0x4
|
|
U8X8_DLY(50),
|
|
U8X8_C(0x28 | 0x6), // CMD_SET_POWER_CONTROL | 0x6
|
|
U8X8_DLY(50),
|
|
U8X8_C(0x28 | 0x7), // CMD_SET_POWER_CONTROL | 0x7
|
|
U8X8_DLY(50),
|
|
U8X8_C(0x20 | 0x6), // CMD_SET_RESISTOR_RATIO | 0x6
|
|
U8X8_END_TRANSFER(),
|
|
U8X8_END() // end of sequence
|
|
};
|
|
|
|
uint8_t u8x8_d_st756x_erc(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr) {
|
|
/* call common procedure first and handle messages there */
|
|
if (u8x8_d_st7565_common(u8x8, msg, arg_int, arg_ptr) == 0) {
|
|
/* msg not handled, then try here */
|
|
switch(msg){
|
|
case U8X8_MSG_DISPLAY_SETUP_MEMORY:
|
|
u8x8_d_helper_display_setup_memory(u8x8, &u8x8_st756x_128x64_display_info);
|
|
break;
|
|
case U8X8_MSG_DISPLAY_INIT:
|
|
u8x8_d_helper_display_init(u8x8);
|
|
u8x8_cad_SendSequence(u8x8, u8x8_d_st756x_erc_init_seq);
|
|
break;
|
|
case U8X8_MSG_DISPLAY_SET_FLIP_MODE:
|
|
if ( arg_int == 0 ) {
|
|
u8x8_cad_SendSequence(u8x8, u8x8_d_st7565_flip1_seq);
|
|
u8x8->x_offset = u8x8->display_info->default_x_offset;
|
|
} else {
|
|
u8x8_cad_SendSequence(u8x8, u8x8_d_st7565_flip0_seq);
|
|
u8x8->x_offset = u8x8->display_info->flipmode_x_offset;
|
|
}
|
|
break;
|
|
default:
|
|
/* msg unknown */
|
|
return 0;
|
|
}
|
|
}
|
|
return 1;
|
|
}
|
|
|
|
void u8g2_Setup_st756x_erc(u8g2_t *u8g2, const u8g2_cb_t *rotation, u8x8_msg_cb byte_cb, u8x8_msg_cb gpio_and_delay_cb) {
|
|
uint8_t tile_buf_height;
|
|
uint8_t *buf;
|
|
u8g2_SetupDisplay(u8g2, u8x8_d_st756x_erc, u8x8_cad_001, byte_cb, gpio_and_delay_cb);
|
|
buf = u8g2_m_16_8_f(&tile_buf_height);
|
|
u8g2_SetupBuffer(u8g2, buf, tile_buf_height, u8g2_ll_hvline_vertical_top_lsb, rotation);
|
|
}
|