flipperzero-firmware/firmware/targets/f5/Src/comp.c
あく 68a3f6b4b7
[FL-873] Add F5 target, lp5562 driver and api-hal-light (#347)
* Add F5 target, lp5562 driver and api-hal-light. Update api-usage, switch to F5 by default.
* API HAL: add i2c and hardware version api. Dolphin: show hardware version.
* OTP version generator and flashing utility.
* Assets script: fix code formatting
* Backport F5 changes to F4
* F4: disable insomnia, prevent damage to BLE RX path
* F5 HAL API Light: remove magic delay to fix magic BLE
* Dolphin: HW target validation on start
* invert RSSI indication in sub-1
* API HAL: rename board to body in version api
* Gpio tester: detach and release viewport on exit

Co-authored-by: aanper <mail@s3f.ru>
2021-02-18 15:49:32 +03:00

104 lines
2.8 KiB
C

/**
******************************************************************************
* @file comp.c
* @brief This file provides code for the configuration
* of the COMP instances.
******************************************************************************
* @attention
*
* <h2><center>&copy; Copyright (c) 2021 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under Ultimate Liberty license
* SLA0044, the "License"; You may not use this file except in compliance with
* the License. You may obtain a copy of the License at:
* www.st.com/SLA0044
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "comp.h"
/* USER CODE BEGIN 0 */
/* USER CODE END 0 */
COMP_HandleTypeDef hcomp1;
/* COMP1 init function */
void MX_COMP1_Init(void)
{
hcomp1.Instance = COMP1;
hcomp1.Init.InputMinus = COMP_INPUT_MINUS_1_4VREFINT;
hcomp1.Init.InputPlus = COMP_INPUT_PLUS_IO1;
hcomp1.Init.OutputPol = COMP_OUTPUTPOL_NONINVERTED;
hcomp1.Init.Hysteresis = COMP_HYSTERESIS_HIGH;
hcomp1.Init.BlankingSrce = COMP_BLANKINGSRC_NONE;
hcomp1.Init.Mode = COMP_POWERMODE_MEDIUMSPEED;
hcomp1.Init.WindowMode = COMP_WINDOWMODE_DISABLE;
hcomp1.Init.TriggerMode = COMP_TRIGGERMODE_IT_RISING_FALLING;
if (HAL_COMP_Init(&hcomp1) != HAL_OK)
{
Error_Handler();
}
}
void HAL_COMP_MspInit(COMP_HandleTypeDef* compHandle)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
if(compHandle->Instance==COMP1)
{
/* USER CODE BEGIN COMP1_MspInit 0 */
/* USER CODE END COMP1_MspInit 0 */
__HAL_RCC_GPIOC_CLK_ENABLE();
/**COMP1 GPIO Configuration
PC5 ------> COMP1_INP
*/
GPIO_InitStruct.Pin = RFID_RF_IN_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(RFID_RF_IN_GPIO_Port, &GPIO_InitStruct);
/* COMP1 interrupt Init */
HAL_NVIC_SetPriority(COMP_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(COMP_IRQn);
/* USER CODE BEGIN COMP1_MspInit 1 */
/* USER CODE END COMP1_MspInit 1 */
}
}
void HAL_COMP_MspDeInit(COMP_HandleTypeDef* compHandle)
{
if(compHandle->Instance==COMP1)
{
/* USER CODE BEGIN COMP1_MspDeInit 0 */
/* USER CODE END COMP1_MspDeInit 0 */
/**COMP1 GPIO Configuration
PC5 ------> COMP1_INP
*/
HAL_GPIO_DeInit(RFID_RF_IN_GPIO_Port, RFID_RF_IN_Pin);
/* COMP1 interrupt Deinit */
HAL_NVIC_DisableIRQ(COMP_IRQn);
/* USER CODE BEGIN COMP1_MspDeInit 1 */
/* USER CODE END COMP1_MspDeInit 1 */
}
}
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/