flipperzero-firmware/lib/ST25RFAL002/st_errno.h
2020-10-20 14:12:28 +03:00

166 lines
8.4 KiB
C

/******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT 2018 STMicroelectronics</center></h2>
*
* Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/myliberty
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
* AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************/
/*
* PROJECT: STxxxx firmware
* LANGUAGE: ISO C99
*/
/*! \file st_errno.h
*
* \author
*
* \brief Main error codes
*
*/
#ifndef ST_ERRNO_H
#define ST_ERRNO_H
/*
******************************************************************************
* INCLUDES
******************************************************************************
*/
#include <stdint.h>
/*
******************************************************************************
* GLOBAL DATA TYPES
******************************************************************************
*/
typedef uint16_t ReturnCode; /*!< Standard Return Code type from function. */
/*
******************************************************************************
* DEFINES
******************************************************************************
*/
/*
* Error codes to be used within the application.
* They are represented by an uint8_t
*/
enum {
ERR_NONE = 0, /*!< no error occurred */
ERR_NOMEM = 1, /*!< not enough memory to perform the requested operation */
ERR_BUSY = 2, /*!< device or resource busy */
ERR_IO = 3, /*!< generic IO error */
ERR_TIMEOUT = 4, /*!< error due to timeout */
ERR_REQUEST = 5, /*!< invalid request or requested function can't be executed at the moment */
ERR_NOMSG = 6, /*!< No message of desired type */
ERR_PARAM = 7, /*!< Parameter error */
ERR_SYSTEM = 8, /*!< System error */
ERR_FRAMING = 9, /*!< Framing error */
ERR_OVERRUN = 10, /*!< lost one or more received bytes */
ERR_PROTO = 11, /*!< protocol error */
ERR_INTERNAL = 12, /*!< Internal Error */
ERR_AGAIN = 13, /*!< Call again */
ERR_MEM_CORRUPT = 14, /*!< memory corruption */
ERR_NOT_IMPLEMENTED = 15, /*!< not implemented */
ERR_PC_CORRUPT = 16, /*!< Program Counter has been manipulated or spike/noise trigger illegal operation */
ERR_SEND = 17, /*!< error sending*/
ERR_IGNORE = 18, /*!< indicates error detected but to be ignored */
ERR_SEMANTIC = 19, /*!< indicates error in state machine (unexpected cmd) */
ERR_SYNTAX = 20, /*!< indicates error in state machine (unknown cmd) */
ERR_CRC = 21, /*!< crc error */
ERR_NOTFOUND = 22, /*!< transponder not found */
ERR_NOTUNIQUE = 23, /*!< transponder not unique - more than one transponder in field */
ERR_NOTSUPP = 24, /*!< requested operation not supported */
ERR_WRITE = 25, /*!< write error */
ERR_FIFO = 26, /*!< fifo over or underflow error */
ERR_PAR = 27, /*!< parity error */
ERR_DONE = 28, /*!< transfer has already finished */
ERR_RF_COLLISION = 29, /*!< collision error (Bit Collision or during RF Collision avoidance ) */
ERR_HW_OVERRUN = 30, /*!< lost one or more received bytes */
ERR_RELEASE_REQ = 31, /*!< device requested release */
ERR_SLEEP_REQ = 32, /*!< device requested sleep */
ERR_WRONG_STATE = 33, /*!< incorrent state for requested operation */
ERR_MAX_RERUNS = 34, /*!< blocking procedure reached maximum runs */
ERR_DISABLED = 35, /*!< operation aborted due to disabled configuration */
ERR_HW_MISMATCH = 36, /*!< expected hw do not match */
ERR_LINK_LOSS = 37, /*!< Other device's field didn't behave as expected: turned off by Initiator in Passive mode, or AP2P did not turn on field */
ERR_INVALID_HANDLE = 38, /*!< invalid or not initalized device handle */
ERR_INCOMPLETE_BYTE = 40, /*!< Incomplete byte rcvd */
ERR_INCOMPLETE_BYTE_01 = 41, /*!< Incomplete byte rcvd - 1 bit */
ERR_INCOMPLETE_BYTE_02 = 42, /*!< Incomplete byte rcvd - 2 bit */
ERR_INCOMPLETE_BYTE_03 = 43, /*!< Incomplete byte rcvd - 3 bit */
ERR_INCOMPLETE_BYTE_04 = 44, /*!< Incomplete byte rcvd - 4 bit */
ERR_INCOMPLETE_BYTE_05 = 45, /*!< Incomplete byte rcvd - 5 bit */
ERR_INCOMPLETE_BYTE_06 = 46, /*!< Incomplete byte rcvd - 6 bit */
ERR_INCOMPLETE_BYTE_07 = 47, /*!< Incomplete byte rcvd - 7 bit */
};
/* General Sub-category number */
#define ERR_GENERIC_GRP (0x0000) /*!< Reserved value for generic error no */
#define ERR_WARN_GRP (0x0100) /*!< Errors which are not expected in normal operation */
#define ERR_PROCESS_GRP (0x0200) /*!< Processes management errors */
#define ERR_SIO_GRP (0x0800) /*!< SIO errors due to logging */
#define ERR_RINGBUF_GRP (0x0900) /*!< Ring Buffer errors */
#define ERR_MQ_GRP (0x0A00) /*!< MQ errors */
#define ERR_TIMER_GRP (0x0B00) /*!< Timer errors */
#define ERR_RFAL_GRP (0x0C00) /*!< RFAL errors */
#define ERR_UART_GRP (0x0D00) /*!< UART errors */
#define ERR_SPI_GRP (0x0E00) /*!< SPI errors */
#define ERR_I2C_GRP (0x0F00) /*!< I2c errors */
#define ERR_INSERT_SIO_GRP(x) (ERR_SIO_GRP | x) /*!< Insert the SIO grp */
#define ERR_INSERT_RINGBUF_GRP(x) (ERR_RINGBUF_GRP | x) /*!< Insert the Ring Buffer grp */
#define ERR_INSERT_RFAL_GRP(x) (ERR_RFAL_GRP | x) /*!< Insert the RFAL grp */
#define ERR_INSERT_SPI_GRP(x) (ERR_SPI_GRP | x) /*!< Insert the spi grp */
#define ERR_INSERT_I2C_GRP(x) (ERR_I2C_GRP | x) /*!< Insert the i2c grp */
#define ERR_INSERT_UART_GRP(x) (ERR_UART_GRP | x) /*!< Insert the uart grp */
#define ERR_INSERT_TIMER_GRP(x) (ERR_TIMER_GRP | x) /*!< Insert the timer grp */
#define ERR_INSERT_MQ_GRP(x) (ERR_MQ_GRP | x) /*!< Insert the mq grp */
#define ERR_INSERT_PROCESS_GRP(x) (ERR_PROCESS_GRP | x) /*!< Insert the process grp */
#define ERR_INSERT_WARN_GRP(x) (ERR_WARN_GRP | x) /*!< Insert the i2c grp */
#define ERR_INSERT_GENERIC_GRP(x) (ERR_GENERIC_GRP | x) /*!< Insert the generic grp */
/*
******************************************************************************
* GLOBAL MACROS
******************************************************************************
*/
#define ERR_NO_MASK(x) (x & 0x00FF) /*!< Mask the error number */
/*! Common code to exit a function with the error if function f return error */
#define EXIT_ON_ERR(r, f) \
if (ERR_NONE != (r = f)) \
{ \
return r; \
}
#endif /* ST_ERRNO_H */