217 lines
4.4 KiB
INI
217 lines
4.4 KiB
INI
|
#This file contains pin mappings for the Lulzbot Mini 1 using RAMBo Mini and SingleExtruder
|
||
|
|
#To use this config, the firmware should be compiled for the AVR atmega2560.
|
||
|
|
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
|
||
|
|
#-------------------------------------------------------------------------------------------------
|
||
|
|
# LULZBOT Mini 1 SingleExtruder (RAMBoMini)
|
||
|
|
# defines are copied from Marlin pins_MINIRAMBO.h
|
||
|
|
# pin conversion was found in fastio_1280.h
|
||
|
|
#-------------------------------------------------------------------------------------------------
|
||
|
|
[stepper_x]
|
||
|
|
#define X_STEP_PIN 37
|
||
|
|
step_pin: PC0
|
||
|
|
#define X_DIR_PIN 48
|
||
|
|
dir_pin: PL1
|
||
|
|
#define X_ENABLE_PIN 29
|
||
|
|
enable_pin: !PA7
|
||
|
|
# 1/100
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 32
|
||
|
|
#define X_MIN_PIN 12
|
||
|
|
endstop_pin: ^!PB6
|
||
|
|
position_endstop: -3
|
||
|
|
position_min: -3
|
||
|
|
position_max: 159
|
||
|
|
homing_speed: 50
|
||
|
|
homing_retract_dist: 2.0
|
||
|
|
second_homing_speed: 5
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
#define Y_STEP_PIN 36
|
||
|
|
step_pin: PC1
|
||
|
|
#define Y_DIR_PIN 49
|
||
|
|
dir_pin: !PL0
|
||
|
|
#define Y_ENABLE_PIN 28
|
||
|
|
enable_pin: !PA6
|
||
|
|
# 1/100
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 32
|
||
|
|
#define Y_MIN_PIN 11
|
||
|
|
endstop_pin: ^!PB5
|
||
|
|
position_endstop: -7
|
||
|
|
position_min: -7
|
||
|
|
position_max: 173
|
||
|
|
homing_speed: 50
|
||
|
|
homing_retract_dist: 2.0
|
||
|
|
second_homing_speed: 5
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
#define Z_STEP_PIN 35
|
||
|
|
step_pin: PC2
|
||
|
|
#define Z_DIR_PIN 47
|
||
|
|
dir_pin: PL2
|
||
|
|
#define Z_ENABLE_PIN 27
|
||
|
|
enable_pin: !PA5
|
||
|
|
# 1/1600
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 2
|
||
|
|
#define Z_MAX_PIN 23
|
||
|
|
endstop_pin: ^!PA1
|
||
|
|
# I have replaced the original nozzle with
|
||
|
|
# a hardened steel one that make the extruder
|
||
|
|
# 1-1.5mm longer, so this may be a little too low
|
||
|
|
position_endstop: 161.5
|
||
|
|
position_max: 161.5
|
||
|
|
position_min: -2.0
|
||
|
|
homing_speed: 7
|
||
|
|
homing_retract_dist: 2.0
|
||
|
|
second_homing_speed: 2
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
#define E0_STEP_PIN 34
|
||
|
|
step_pin: PC3
|
||
|
|
#define E0_DIR_PIN 43
|
||
|
|
dir_pin: !PL6
|
||
|
|
#define E0_ENABLE_PIN 26
|
||
|
|
enable_pin: !PA4
|
||
|
|
# 1/833
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 3.842
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 2.850
|
||
|
|
#define HEATER_0_PIN 3
|
||
|
|
heater_pin: PE5
|
||
|
|
#The Extruder uses 100K thermistor - ATC Semitec 104GT-2 (#5) and PID control
|
||
|
|
sensor_type: ATC Semitec 104GT-2
|
||
|
|
# I can't explain this from Marlin
|
||
|
|
sensor_pin: PF0
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 28.79
|
||
|
|
pid_Ki: 1.91
|
||
|
|
pid_Kd: 108.51
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 280
|
||
|
|
min_extrude_temp: 160
|
||
|
|
max_extrude_only_velocity: 500
|
||
|
|
max_extrude_only_accel: 2000
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
#define HEATER_BED_PIN 4
|
||
|
|
heater_pin: PG5
|
||
|
|
# The Heater Bed uses Honeywell 100K 135-104LAG-J01 temp sensor (#7) and PID control
|
||
|
|
sensor_type: Honeywell 100K 135-104LAG-J01
|
||
|
|
# I can't explain this from Marlin
|
||
|
|
sensor_pin: PF2
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 294.0
|
||
|
|
pid_Ki: 65.0
|
||
|
|
pid_Kd: 382.0
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 130
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
#define FAN_PIN 8
|
||
|
|
pin: PH5
|
||
|
|
|
||
|
|
[heater_fan heatbreak_cooling_fan]
|
||
|
|
#define FAN1_PIN 6
|
||
|
|
pin: PH3
|
||
|
|
|
||
|
|
[output_pin stepper_xy_current]
|
||
|
|
#define MOTOR_CURRENT_PWM_XY_PIN 46
|
||
|
|
pin: PL3
|
||
|
|
pwm: True
|
||
|
|
scale: 2.0
|
||
|
|
cycle_time: .000030
|
||
|
|
hardware_pwm: True
|
||
|
|
value: 1.300
|
||
|
|
|
||
|
|
[output_pin stepper_z_current]
|
||
|
|
pin: PL4
|
||
|
|
pwm: True
|
||
|
|
scale: 2.0
|
||
|
|
cycle_time: .000030
|
||
|
|
hardware_pwm: True
|
||
|
|
value: 1.630
|
||
|
|
|
||
|
|
[output_pin stepper_e_current]
|
||
|
|
pin: PL5
|
||
|
|
pwm: True
|
||
|
|
scale: 2.0
|
||
|
|
cycle_time: .000030
|
||
|
|
hardware_pwm: True
|
||
|
|
value: 1.250
|
||
|
|
|
||
|
|
[static_digital_output stepper_config]
|
||
|
|
# Microstepping pins
|
||
|
|
#define X_MS1_PIN 40
|
||
|
|
#define X_MS2_PIN 41
|
||
|
|
#define Y_MS1_PIN 69
|
||
|
|
#define Y_MS2_PIN 39
|
||
|
|
#define Z_MS1_PIN 68
|
||
|
|
#define Z_MS2_PIN 67
|
||
|
|
#define E0_MS1_PIN 65
|
||
|
|
#define E0_MS2_PIN 66
|
||
|
|
pins:
|
||
|
|
PG1, PG0,
|
||
|
|
PK7, PG2,
|
||
|
|
PK6, PK5,
|
||
|
|
PK3, PK4
|
||
|
|
|
||
|
|
[static_digital_output yellow_led]
|
||
|
|
#define LED_PIN 13
|
||
|
|
pins: !PB7
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/ttyACM0
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 2000
|
||
|
|
max_z_velocity: 7
|
||
|
|
max_z_accel: 500
|
||
|
|
|
||
|
|
[homing_override]
|
||
|
|
gcode:
|
||
|
|
G91
|
||
|
|
G28 Z
|
||
|
|
G0 Z-5
|
||
|
|
G28 X Y
|
||
|
|
G0 X3 Y7
|
||
|
|
G90
|
||
|
|
|
||
|
|
[probe]
|
||
|
|
#define Z_MIN_PROBE_PIN 10
|
||
|
|
pin: ^!PB4
|
||
|
|
# z_offset equals washer thickness ~= 1.377
|
||
|
|
z_offset: 1.377
|
||
|
|
speed: 5.0
|
||
|
|
samples: 2
|
||
|
|
sample_retract_dist: 1.0
|
||
|
|
samples_result: average
|
||
|
|
samples_tolerance: 0.200
|
||
|
|
samples_tolerance_retries: 2
|
||
|
|
|
||
|
|
[bed_tilt]
|
||
|
|
# Enable bed tilt measurments using the probe we defined above
|
||
|
|
# Probe points using X0 Y0 offsets @ 0.01mm/step
|
||
|
|
points: -2, -6
|
||
|
|
156, -6
|
||
|
|
156, 158
|
||
|
|
-2, 158
|
||
|
|
speed: 75
|
||
|
|
horizontal_move_z: 2
|
||
|
|
|
||
|
|
[firmware_retraction]
|
||
|
|
retract_length: 2
|
||
|
|
retract_speed: 200
|
||
|
|
unretract_extra_length: 0
|
||
|
|
unretract_speed: 200
|
||
|
|
|
||
|
|
[gcode_macro G29]
|
||
|
|
# Preform the ABL by running G29 in the start GCODE script
|
||
|
|
gcode:
|
||
|
|
BED_TILT_CALIBRATE
|