club_configs/mini.cfg

@@ -1,216 +0,0 @@
-#This file contains pin mappings for the Lulzbot Mini 1 using RAMBo Mini and SingleExtruder
-#To use this config, the firmware should be compiled for the AVR atmega2560.
-
-# See docs/Config_Reference.md for a description of parameters.
-
-#-------------------------------------------------------------------------------------------------
-# LULZBOT Mini 1 SingleExtruder (RAMBoMini)
-# defines are copied from Marlin pins_MINIRAMBO.h
-# pin conversion was found in fastio_1280.h
-#-------------------------------------------------------------------------------------------------
-[stepper_x]
-#define X_STEP_PIN         37
-step_pin: PC0
-#define X_DIR_PIN          48
-dir_pin: PL1
-#define X_ENABLE_PIN       29
-enable_pin: !PA7
-# 1/100
-microsteps: 16
-rotation_distance: 32
-#define X_MIN_PIN          12
-endstop_pin: ^!PB6
-position_endstop: -3
-position_min: -3
-position_max: 159
-homing_speed: 50
-homing_retract_dist: 2.0
-second_homing_speed: 5
-
-[stepper_y]
-#define Y_STEP_PIN         36
-step_pin: PC1
-#define Y_DIR_PIN          49
-dir_pin: !PL0
-#define Y_ENABLE_PIN       28
-enable_pin: !PA6
-# 1/100
-microsteps: 16
-rotation_distance: 32
-#define Y_MIN_PIN          11
-endstop_pin: ^!PB5
-position_endstop: -7
-position_min: -7
-position_max: 173
-homing_speed: 50
-homing_retract_dist: 2.0
-second_homing_speed: 5
-
-[stepper_z]
-#define Z_STEP_PIN         35
-step_pin: PC2
-#define Z_DIR_PIN          47
-dir_pin: PL2
-#define Z_ENABLE_PIN       27
-enable_pin: !PA5
-# 1/1600
-microsteps: 16
-rotation_distance: 2
-#define Z_MAX_PIN          23
-endstop_pin: ^!PA1
-# I have replaced the original nozzle with
-# a hardened steel one that make the extruder
-# 1-1.5mm longer, so this may be a little too low
-position_endstop: 161.5
-position_max: 161.5
-position_min: -2.0
-homing_speed: 7
-homing_retract_dist: 2.0
-second_homing_speed: 2
-
-[extruder]
-#define E0_STEP_PIN        34
-step_pin: PC3
-#define E0_DIR_PIN         43
-dir_pin: !PL6
-#define E0_ENABLE_PIN      26
-enable_pin: !PA4
-# 1/833
-microsteps: 16
-rotation_distance: 3.842
-nozzle_diameter: 0.400
-filament_diameter: 2.850
-#define HEATER_0_PIN        3
-heater_pin: PE5
-#The Extruder uses 100K thermistor - ATC Semitec 104GT-2 (#5) and PID control
-sensor_type: ATC Semitec 104GT-2
-# I can't explain this from Marlin
-sensor_pin: PF0
-control: pid
-pid_Kp: 28.79
-pid_Ki: 1.91
-pid_Kd: 108.51
-min_temp: 0
-max_temp: 280
-min_extrude_temp: 160
-max_extrude_only_velocity: 500
-max_extrude_only_accel: 2000
-
-[heater_bed]
-#define HEATER_BED_PIN      4
-heater_pin: PG5
-# The Heater Bed uses Honeywell 100K 135-104LAG-J01 temp sensor (#7) and PID control
-sensor_type: Honeywell 100K 135-104LAG-J01
-# I can't explain this from Marlin
-sensor_pin: PF2
-control: pid
-pid_Kp: 294.0
-pid_Ki: 65.0
-pid_Kd: 382.0
-min_temp: 0
-max_temp: 130
-
-[fan]
-#define FAN_PIN             8
-pin: PH5
-
-[heater_fan heatbreak_cooling_fan]
-#define FAN1_PIN            6
-pin: PH3
-
-[output_pin stepper_xy_current]
-#define MOTOR_CURRENT_PWM_XY_PIN 46
-pin: PL3
-pwm: True
-scale: 2.0
-cycle_time: .000030
-hardware_pwm: True
-value: 1.300
-
-[output_pin stepper_z_current]
-pin: PL4
-pwm: True
-scale: 2.0
-cycle_time: .000030
-hardware_pwm: True
-value: 1.630
-
-[output_pin stepper_e_current]
-pin: PL5
-pwm: True
-scale: 2.0
-cycle_time: .000030
-hardware_pwm: True
-value: 1.250
-
-[static_digital_output stepper_config]
-# Microstepping pins
-#define X_MS1_PIN          40
-#define X_MS2_PIN          41
-#define Y_MS1_PIN          69
-#define Y_MS2_PIN          39
-#define Z_MS1_PIN          68
-#define Z_MS2_PIN          67
-#define E0_MS1_PIN         65
-#define E0_MS2_PIN         66
-pins:
-    PG1, PG0,
-    PK7, PG2,
-    PK6, PK5,
-    PK3, PK4
-
-[static_digital_output yellow_led]
-#define LED_PIN            13
-pins: !PB7
-
-[mcu]
-serial: /dev/ttyACM0
-
-[printer]
-kinematics: cartesian
-max_velocity: 300
-max_accel: 2000
-max_z_velocity: 7
-max_z_accel: 500
-
-[homing_override]
-gcode:
-  G91
-  G28 Z
-  G0 Z-5
-  G28 X Y
-  G0 X3 Y7
-  G90
-
-[probe]
-#define Z_MIN_PROBE_PIN  10
-pin: ^!PB4
-# z_offset equals washer thickness ~= 1.377
-z_offset: 1.377
-speed: 5.0
-samples: 2
-sample_retract_dist: 1.0
-samples_result: average
-samples_tolerance: 0.200
-samples_tolerance_retries: 2
-
-[bed_tilt]
-# Enable bed tilt measurments using the probe we defined above
-# Probe points using X0 Y0 offsets @ 0.01mm/step
-points: -2, -6
-        156, -6
-        156, 158
-        -2, 158
-speed: 75
-horizontal_move_z: 2
-
-[firmware_retraction]
-retract_length: 2
-retract_speed: 200
-unretract_extra_length: 0
-unretract_speed: 200
-
-[gcode_macro G29]
-# Preform the ABL by running G29 in the start GCODE script
-gcode:
-    BED_TILT_CALIBRATE

setup.sh

@@ -148,9 +148,7 @@ if [[ "$ARG_PORT" == 0 ]]; then
         while [ ! -f "${MANUAL_FILE}" ]; do
             MANUAL_FILE=$(dialog --backtitle "drwho@hackers.town" --title "Manual Device Selection" --inputbox "Enter Full Device File Path" 8 40 "${MANUAL_FILE}" 3>&1 1>&2 2>&3)
         done
-        DEVICE="$MANUAL_FILE"
+        DEVICE="/dev/serial/by-id/$MANUAL_FILE"
-    else
-        DEVICE="/dev/serial/by-id/$DEVICE"
     fi
 else
     echo.ICyan "Using passed serial port"
@@ -208,21 +206,21 @@ echo.ICyan "Installing base nginx configs"
 if [ ! -f /etc/nginx/conf.d/upstreams.conf ]; then
     sudo cp $ROOT_DIR/config/nginx/upstreams.conf /etc/nginx/conf.d/upstreams.conf
     sudo chown root:root /etc/nginx/conf.d/upstreams.conf
-else
+else 
     echo.ICyan "upstreams.conf already exists"
 fi
 
 if [ ! -f /etc/nginx/sites-available/site.conf ]; then
     sudo cp $ROOT_DIR/config/nginx/site.conf /etc/nginx/sites-available/site.conf
     sudo chown root:root /etc/nginx/sites-available/site.conf
-else
+else 
     echo.ICyan "site.conf already exists"
 fi
 
 if [ ! -f /etc/nginx/conf.d/common_vars.conf ]; then
     sudo cp $ROOT_DIR/config/nginx/common_vars.conf /etc/nginx/conf.d/common_vars.conf
     sudo chown root:root /etc/nginx/conf.d/common_vars.conf
-else
+else 
     echo.ICyan "common_vars.conf already exists"
 fi
 
@@ -321,4 +319,4 @@ if [ ! -f /etc/nginx/sites-enabled/site.conf ]; then
     echo.Red "NGINX config not enabled, don't forget to symlink the site.conf file from sites-available to sites-enabled"
 else
     sudo systemctl start nginx
-fi
+fi