Compare commits
No commits in common. "main" and "mvp-printerconfig" have entirely different histories.
main
...
mvp-printe
@ -1,216 +0,0 @@
|
||||
#This file contains pin mappings for the Lulzbot Mini 1 using RAMBo Mini and SingleExtruder
|
||||
#To use this config, the firmware should be compiled for the AVR atmega2560.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
#-------------------------------------------------------------------------------------------------
|
||||
# LULZBOT Mini 1 SingleExtruder (RAMBoMini)
|
||||
# defines are copied from Marlin pins_MINIRAMBO.h
|
||||
# pin conversion was found in fastio_1280.h
|
||||
#-------------------------------------------------------------------------------------------------
|
||||
[stepper_x]
|
||||
#define X_STEP_PIN 37
|
||||
step_pin: PC0
|
||||
#define X_DIR_PIN 48
|
||||
dir_pin: PL1
|
||||
#define X_ENABLE_PIN 29
|
||||
enable_pin: !PA7
|
||||
# 1/100
|
||||
microsteps: 16
|
||||
rotation_distance: 32
|
||||
#define X_MIN_PIN 12
|
||||
endstop_pin: ^!PB6
|
||||
position_endstop: -3
|
||||
position_min: -3
|
||||
position_max: 159
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 2.0
|
||||
second_homing_speed: 5
|
||||
|
||||
[stepper_y]
|
||||
#define Y_STEP_PIN 36
|
||||
step_pin: PC1
|
||||
#define Y_DIR_PIN 49
|
||||
dir_pin: !PL0
|
||||
#define Y_ENABLE_PIN 28
|
||||
enable_pin: !PA6
|
||||
# 1/100
|
||||
microsteps: 16
|
||||
rotation_distance: 32
|
||||
#define Y_MIN_PIN 11
|
||||
endstop_pin: ^!PB5
|
||||
position_endstop: -7
|
||||
position_min: -7
|
||||
position_max: 173
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 2.0
|
||||
second_homing_speed: 5
|
||||
|
||||
[stepper_z]
|
||||
#define Z_STEP_PIN 35
|
||||
step_pin: PC2
|
||||
#define Z_DIR_PIN 47
|
||||
dir_pin: PL2
|
||||
#define Z_ENABLE_PIN 27
|
||||
enable_pin: !PA5
|
||||
# 1/1600
|
||||
microsteps: 16
|
||||
rotation_distance: 2
|
||||
#define Z_MAX_PIN 23
|
||||
endstop_pin: ^!PA1
|
||||
# I have replaced the original nozzle with
|
||||
# a hardened steel one that make the extruder
|
||||
# 1-1.5mm longer, so this may be a little too low
|
||||
position_endstop: 161.5
|
||||
position_max: 161.5
|
||||
position_min: -2.0
|
||||
homing_speed: 7
|
||||
homing_retract_dist: 2.0
|
||||
second_homing_speed: 2
|
||||
|
||||
[extruder]
|
||||
#define E0_STEP_PIN 34
|
||||
step_pin: PC3
|
||||
#define E0_DIR_PIN 43
|
||||
dir_pin: !PL6
|
||||
#define E0_ENABLE_PIN 26
|
||||
enable_pin: !PA4
|
||||
# 1/833
|
||||
microsteps: 16
|
||||
rotation_distance: 3.842
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 2.850
|
||||
#define HEATER_0_PIN 3
|
||||
heater_pin: PE5
|
||||
#The Extruder uses 100K thermistor - ATC Semitec 104GT-2 (#5) and PID control
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
# I can't explain this from Marlin
|
||||
sensor_pin: PF0
|
||||
control: pid
|
||||
pid_Kp: 28.79
|
||||
pid_Ki: 1.91
|
||||
pid_Kd: 108.51
|
||||
min_temp: 0
|
||||
max_temp: 280
|
||||
min_extrude_temp: 160
|
||||
max_extrude_only_velocity: 500
|
||||
max_extrude_only_accel: 2000
|
||||
|
||||
[heater_bed]
|
||||
#define HEATER_BED_PIN 4
|
||||
heater_pin: PG5
|
||||
# The Heater Bed uses Honeywell 100K 135-104LAG-J01 temp sensor (#7) and PID control
|
||||
sensor_type: Honeywell 100K 135-104LAG-J01
|
||||
# I can't explain this from Marlin
|
||||
sensor_pin: PF2
|
||||
control: pid
|
||||
pid_Kp: 294.0
|
||||
pid_Ki: 65.0
|
||||
pid_Kd: 382.0
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
#define FAN_PIN 8
|
||||
pin: PH5
|
||||
|
||||
[heater_fan heatbreak_cooling_fan]
|
||||
#define FAN1_PIN 6
|
||||
pin: PH3
|
||||
|
||||
[output_pin stepper_xy_current]
|
||||
#define MOTOR_CURRENT_PWM_XY_PIN 46
|
||||
pin: PL3
|
||||
pwm: True
|
||||
scale: 2.0
|
||||
cycle_time: .000030
|
||||
hardware_pwm: True
|
||||
value: 1.300
|
||||
|
||||
[output_pin stepper_z_current]
|
||||
pin: PL4
|
||||
pwm: True
|
||||
scale: 2.0
|
||||
cycle_time: .000030
|
||||
hardware_pwm: True
|
||||
value: 1.630
|
||||
|
||||
[output_pin stepper_e_current]
|
||||
pin: PL5
|
||||
pwm: True
|
||||
scale: 2.0
|
||||
cycle_time: .000030
|
||||
hardware_pwm: True
|
||||
value: 1.250
|
||||
|
||||
[static_digital_output stepper_config]
|
||||
# Microstepping pins
|
||||
#define X_MS1_PIN 40
|
||||
#define X_MS2_PIN 41
|
||||
#define Y_MS1_PIN 69
|
||||
#define Y_MS2_PIN 39
|
||||
#define Z_MS1_PIN 68
|
||||
#define Z_MS2_PIN 67
|
||||
#define E0_MS1_PIN 65
|
||||
#define E0_MS2_PIN 66
|
||||
pins:
|
||||
PG1, PG0,
|
||||
PK7, PG2,
|
||||
PK6, PK5,
|
||||
PK3, PK4
|
||||
|
||||
[static_digital_output yellow_led]
|
||||
#define LED_PIN 13
|
||||
pins: !PB7
|
||||
|
||||
[mcu]
|
||||
serial: /dev/ttyACM0
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 2000
|
||||
max_z_velocity: 7
|
||||
max_z_accel: 500
|
||||
|
||||
[homing_override]
|
||||
gcode:
|
||||
G91
|
||||
G28 Z
|
||||
G0 Z-5
|
||||
G28 X Y
|
||||
G0 X3 Y7
|
||||
G90
|
||||
|
||||
[probe]
|
||||
#define Z_MIN_PROBE_PIN 10
|
||||
pin: ^!PB4
|
||||
# z_offset equals washer thickness ~= 1.377
|
||||
z_offset: 1.377
|
||||
speed: 5.0
|
||||
samples: 2
|
||||
sample_retract_dist: 1.0
|
||||
samples_result: average
|
||||
samples_tolerance: 0.200
|
||||
samples_tolerance_retries: 2
|
||||
|
||||
[bed_tilt]
|
||||
# Enable bed tilt measurments using the probe we defined above
|
||||
# Probe points using X0 Y0 offsets @ 0.01mm/step
|
||||
points: -2, -6
|
||||
156, -6
|
||||
156, 158
|
||||
-2, 158
|
||||
speed: 75
|
||||
horizontal_move_z: 2
|
||||
|
||||
[firmware_retraction]
|
||||
retract_length: 2
|
||||
retract_speed: 200
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 200
|
||||
|
||||
[gcode_macro G29]
|
||||
# Preform the ABL by running G29 in the start GCODE script
|
||||
gcode:
|
||||
BED_TILT_CALIBRATE
|
||||
@ -1,214 +0,0 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH SKR mini
|
||||
# E3 v3.0. To use this config, the firmware should be compiled for the
|
||||
# STM32G0B1 with a "8KiB bootloader" and USB communication.
|
||||
|
||||
# The "make flash" command does not work on the SKR mini E3. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR
|
||||
# mini E3 with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
[gcode_macro CALIBRATE_NOZZLE_OFFSET]
|
||||
description: Move to center of bed and calibrate nozzle offset
|
||||
gcode:
|
||||
G90
|
||||
G0 X100 Y155 F1500
|
||||
PROBE_CALIBRATE
|
||||
|
||||
[gcode_macro LEVEL_BED]
|
||||
description: "Level the bed manually."
|
||||
gcode:
|
||||
BED_SCREWS_ADJUST
|
||||
|
||||
[gcode_macro CHECK_DEVIATION]
|
||||
description: "Check the deviation of the bed from the last loaded mesh."
|
||||
gcode:
|
||||
SCREWS_TILT_CALCULATE MAX_DEVIATION=0.05
|
||||
|
||||
[gcode_macro LIZ_IS_A_BAKA]
|
||||
description: "Liz is a baka, so here's her start G-Code >.<"
|
||||
gcode:
|
||||
BED_MESH_CALIBRATE
|
||||
BED_MESH_PROFILE SAVE=default
|
||||
|
||||
[gcode_macro _START_GCODE]
|
||||
description: "The gcode that should be called from your slicer at the beginning of a print."
|
||||
gcode:
|
||||
# Ender 3 Custom Start G-code
|
||||
G90
|
||||
G1 X2 Y30 Z30 F1500
|
||||
G1 Z0.28 F240
|
||||
G92 E0
|
||||
G1 Y220 E10 F1500 ; prime the nozzle
|
||||
G1 X2.3 F5000
|
||||
G92 E0
|
||||
G1 Y30 E10 F1200 ; prime the nozzle
|
||||
G92 E0
|
||||
G1 Z5 F1500 ; don't scratch the build plate
|
||||
|
||||
[gcode_macro _END_GCODE]
|
||||
description: "The gcode that should be called from your slicer at the end of a print."
|
||||
gcode:
|
||||
G91 # Relative positioning
|
||||
G1 E-2 F2700 # Retract a bit
|
||||
G1 E-2 Z0.2 F2400 # Retract and raise Z
|
||||
G1 X5 Y5 F3000 # Wipe out
|
||||
G1 Z10 # Raise Z more
|
||||
G90 # Absolute positioning
|
||||
|
||||
G1 X0 Y220 # Present print
|
||||
M106 S0 # Turn-off fan
|
||||
M104 S0 # Turn-off hotend
|
||||
M140 S0 # Turn-off bed
|
||||
|
||||
M84 X Y E # Disable all steppers but Z
|
||||
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB13
|
||||
dir_pin: !PB12
|
||||
enable_pin: !PB14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC0
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PC11
|
||||
tx_pin: PC10
|
||||
uart_address: 0
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB10
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PC1
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC11
|
||||
tx_pin: PC10
|
||||
uart_address: 2
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB0
|
||||
dir_pin: PC5
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0.0
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC11
|
||||
tx_pin: PC10
|
||||
uart_address: 1
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: PC14
|
||||
control_pin: PA1
|
||||
x_offset: -44
|
||||
y_offset: 8
|
||||
probe_with_touch_mode: True
|
||||
# pin_up_touch_mode_reports_triggered = False
|
||||
# z_offset: 3.0
|
||||
|
||||
[bed_mesh]
|
||||
speed: 120
|
||||
horizontal_move_z: 7
|
||||
mesh_min: 30, 40
|
||||
mesh_max: 250, 230
|
||||
probe_count: 5
|
||||
mesh_pps: 3
|
||||
algorithm: bicubic
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 140, 140
|
||||
speed: 50
|
||||
z_hop: 10
|
||||
z_hop_speed: 5
|
||||
|
||||
[extruder]
|
||||
step_pin: PB3
|
||||
dir_pin: !PB4
|
||||
enable_pin: !PD1
|
||||
microsteps: 16
|
||||
rotation_distance: 7.9797
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC8
|
||||
# sensor_type: EPCOS 100K B57560G104F # Stock board config
|
||||
sensor_type: NTC 100K MGB18-104F39050L32
|
||||
sensor_pin: PA0
|
||||
control: pid
|
||||
pid_Kp: 21.527
|
||||
pid_Ki: 1.063
|
||||
pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 300
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
tx_pin: PC10
|
||||
uart_address: 3
|
||||
run_current: 0.650
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC9
|
||||
# sensor_type: ATC Semitec 104GT-2 # Stock board config
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC4
|
||||
control: pid
|
||||
pid_Kp: 54.027
|
||||
pid_Ki: 0.770
|
||||
pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[heater_fan heatbreak_cooling_fan]
|
||||
pin: PC6
|
||||
fan_speed: 1.0
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
|
||||
[fan cooling]
|
||||
pin: PC7 # Part cooling
|
||||
|
||||
# [heater_fan controller_fan]
|
||||
# pin: PB15
|
||||
|
||||
# [fan]
|
||||
# pin: PC6
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||
EXP1_2=PA15, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PD6, EXP1_10=<5V>
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
[include mainsail.cfg]
|
||||
40
setup.sh
40
setup.sh
@ -3,7 +3,6 @@
|
||||
# TODO: Add Crowsnest Support
|
||||
# TODO: Dry run
|
||||
# TODO: Printer Directory Page in NGINX
|
||||
# TODO: Add mainsail GCODE if config not manually entered
|
||||
|
||||
# Handle arguments
|
||||
ARG_HELP=0
|
||||
@ -11,7 +10,6 @@ ARG_SKIP_APT=0
|
||||
ARG_NAME=0
|
||||
ARG_CONFIG=0
|
||||
ARG_PORT=0
|
||||
ARG_FIRM=0
|
||||
while [[ "$#" -gt 0 ]]; do
|
||||
case $1 in
|
||||
-h|--help) ARG_HELP=1 ;;
|
||||
@ -19,7 +17,6 @@ while [[ "$#" -gt 0 ]]; do
|
||||
-n|--name) ARG_NAME="$2" ; shift ;;
|
||||
-c|--config) ARG_CONFIG="$2" ; shift ;;
|
||||
-p|--port) ARG_PORT="$2" ; shift ;;
|
||||
-f|--skip-firmware) ARG_FIRM=1 ;;
|
||||
*) echo "Unknown Parameter"; exit 3 ;;
|
||||
esac
|
||||
shift
|
||||
@ -43,13 +40,12 @@ cd $ROOT_DIR
|
||||
source ./ColorEchoForShell/dist/ColorEcho.bash
|
||||
|
||||
if [[ "$ARG_HELP" == 1 ]]; then
|
||||
echo.Cyan "HacDC Printer Setup Script Usage"
|
||||
echo.Cyan "HacDC Printewr Setup Script Usage"
|
||||
echo.Yellow "./setup.sh [options]"
|
||||
echo ""
|
||||
echo.BoldPurple "Option Description"
|
||||
echo.Rainbow "-h/--help Display this help msg"
|
||||
echo.Rainbow "-a/--skip-apt Skip installing apt packages"
|
||||
echo.Rainbow "-f/--skip-firmware Skip firmware build/install"
|
||||
echo.Rainbow "-n/--name Specify printer name (skips popup)"
|
||||
echo.Rainbow "-c/--config Specify printer config (skips popup)"
|
||||
echo.Rainbow "-p/--port Specify printer port (skips popup)"
|
||||
@ -105,10 +101,7 @@ cp -r $ROOT_DIR/dirs $ROOT_DIR/$PRINTER_NAME
|
||||
|
||||
# Select Klipper Config
|
||||
cd $ROOT_DIR/$PRINTER_NAME/klipper
|
||||
if [[ "$ARG_FIRM" == 0 ]]; then
|
||||
make menuconfig
|
||||
fi
|
||||
|
||||
make menuconfig
|
||||
CONFIG_FILE=""
|
||||
if [[ "$ARG_CONFIG" == 0 ]]; then
|
||||
CONFIG_FILES=(`ls config`)
|
||||
@ -155,9 +148,7 @@ if [[ "$ARG_PORT" == 0 ]]; then
|
||||
while [ ! -f "${MANUAL_FILE}" ]; do
|
||||
MANUAL_FILE=$(dialog --backtitle "drwho@hackers.town" --title "Manual Device Selection" --inputbox "Enter Full Device File Path" 8 40 "${MANUAL_FILE}" 3>&1 1>&2 2>&3)
|
||||
done
|
||||
DEVICE="$MANUAL_FILE"
|
||||
else
|
||||
DEVICE="/dev/serial/by-id/$DEVICE"
|
||||
DEVICE="/dev/serial/by-id/$MANUAL_FILE"
|
||||
fi
|
||||
else
|
||||
echo.ICyan "Using passed serial port"
|
||||
@ -165,20 +156,17 @@ else
|
||||
fi
|
||||
|
||||
# Build Klipper
|
||||
if [[ "$ARG_FIRM" == 0 ]]; then
|
||||
echo.Cyan "Compile Klipper Firmware"
|
||||
cp $CONFIG_FILE $ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg
|
||||
sed -i -e "s/^serial: .\+$/LINEHERE/g" "$ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg"
|
||||
cat $ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg | replace "LINEHERE" "serial: $DEVICE" > $ROOT_DIR/$PRINTER_NAME/klipper/tmp.cfg
|
||||
rm $ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg
|
||||
mv $ROOT_DIR/$PRINTER_NAME/klipper/tmp.cfg $ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg
|
||||
make -j$(nproc)
|
||||
# Flash Firmware
|
||||
echo.Cyan "Flash Device"
|
||||
make flash FLASH_DEVICE=$DEVICE
|
||||
else
|
||||
echo.ICyan "Skipping firmware build"
|
||||
fi
|
||||
echo.Cyan "Compile Klipper Firmware"
|
||||
cp $CONFIG_FILE $ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg
|
||||
sed -i -e "s/^serial: .\+$/LINEHERE/g" "$ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg"
|
||||
cat $ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg | replace "LINEHERE" "serial: $DEVICE" > $ROOT_DIR/$PRINTER_NAME/klipper/tmp.cfg
|
||||
rm $ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg
|
||||
mv $ROOT_DIR/$PRINTER_NAME/klipper/tmp.cfg $ROOT_DIR/$PRINTER_NAME/klipper/printer.cfg
|
||||
make -j$(nproc)
|
||||
|
||||
# Flash Firmware
|
||||
echo.Cyan "Flash Device"
|
||||
make flash FLASH_DEVICE=$DEVICE
|
||||
|
||||
# Copy over printer config file
|
||||
echo.Cyan "Setup printer.cfg"
|
||||
|
||||
Loading…
Reference in New Issue
Block a user