106 lines
2.7 KiB
INI
106 lines
2.7 KiB
INI
|
# script for stm32wbx family
|
||
|
|
|
||
|
|
gdb_port 4242
|
||
|
|
|
||
|
|
#
|
||
|
|
# stm32wb devices support both JTAG and SWD transports.
|
||
|
|
#
|
||
|
|
source [find target/swj-dp.tcl]
|
||
|
|
source [find mem_helper.tcl]
|
||
|
|
|
||
|
|
if { [info exists CHIPNAME] } {
|
||
|
|
set _CHIPNAME $CHIPNAME
|
||
|
|
} else {
|
||
|
|
set _CHIPNAME stm32wbx
|
||
|
|
}
|
||
|
|
|
||
|
|
set _ENDIAN little
|
||
|
|
|
||
|
|
# Work-area is a space in RAM used for flash programming
|
||
|
|
# By default use 64kB
|
||
|
|
if { [info exists WORKAREASIZE] } {
|
||
|
|
set _WORKAREASIZE $WORKAREASIZE
|
||
|
|
} else {
|
||
|
|
set _WORKAREASIZE 0x10000
|
||
|
|
}
|
||
|
|
|
||
|
|
#jtag scan chain
|
||
|
|
if { [info exists CPUTAPID] } {
|
||
|
|
set _CPUTAPID $CPUTAPID
|
||
|
|
} else {
|
||
|
|
if { [using_jtag] } {
|
||
|
|
set _CPUTAPID 0x6ba00477
|
||
|
|
} else {
|
||
|
|
# SWD IDCODE (single drop, arm)
|
||
|
|
set _CPUTAPID 0x6ba02477
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
||
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
||
|
|
|
||
|
|
if {[using_jtag]} {
|
||
|
|
jtag newtap $_CHIPNAME bs -irlen 5
|
||
|
|
}
|
||
|
|
|
||
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
||
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
||
|
|
|
||
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
||
|
|
|
||
|
|
set _FLASHNAME $_CHIPNAME.flash
|
||
|
|
flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
|
||
|
|
|
||
|
|
# Common knowledges tells JTAG speed should be <= F_CPU/6.
|
||
|
|
# F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
|
||
|
|
# the safe side.
|
||
|
|
#
|
||
|
|
# Note that there is a pretty wide band where things are
|
||
|
|
# more or less stable, see http://openocd.zylin.com/#/c/3366/
|
||
|
|
adapter speed 500
|
||
|
|
|
||
|
|
adapter srst delay 100
|
||
|
|
if {[using_jtag]} {
|
||
|
|
jtag_ntrst_delay 100
|
||
|
|
}
|
||
|
|
|
||
|
|
reset_config srst_nogate
|
||
|
|
|
||
|
|
if {![using_hla]} {
|
||
|
|
# if srst is not fitted use SYSRESETREQ to
|
||
|
|
# perform a soft reset
|
||
|
|
cortex_m reset_config sysresetreq
|
||
|
|
}
|
||
|
|
|
||
|
|
$_TARGETNAME configure -event reset-init {
|
||
|
|
# CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 4 MHz.
|
||
|
|
# Configure system to use MSI 24 MHz clock, compliant with VOS default Range1.
|
||
|
|
# 2 WS compliant with VOS=Range1 and 24 MHz.
|
||
|
|
mmw 0x58004000 0x00000102 0 ;# FLASH_ACR |= PRFTBE | 2(Latency)
|
||
|
|
mmw 0x58000000 0x00000091 0 ;# RCC_CR = MSI_ON | MSI Range 24 MHz
|
||
|
|
# Boost JTAG frequency
|
||
|
|
adapter speed 4000
|
||
|
|
}
|
||
|
|
|
||
|
|
$_TARGETNAME configure -event reset-start {
|
||
|
|
# Reset clock is MSI (4 MHz)
|
||
|
|
adapter speed 500
|
||
|
|
}
|
||
|
|
|
||
|
|
$_TARGETNAME configure -event examine-end {
|
||
|
|
# Enable debug during low power modes (uses more power)
|
||
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
|
||
|
|
mmw 0xE0042004 0x00000007 0
|
||
|
|
|
||
|
|
# Stop watchdog counters during halt
|
||
|
|
# DBGMCU_APB1_FZR1 |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
||
|
|
mmw 0xE004203C 0x00001800 0
|
||
|
|
}
|
||
|
|
|
||
|
|
$_TARGETNAME configure -event trace-config {
|
||
|
|
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
|
||
|
|
# change this value accordingly to configure trace pins
|
||
|
|
# assignment
|
||
|
|
mmw 0xE0042004 0x00000020 0
|
||
|
|
}
|