hacdc-klipper/club_configs/taz.cfg

# This file contains common pin mappings for the BIGTREETECH SKR mini
# E3 v3.0. To use this config, the firmware should be compiled for the
# STM32G0B1 with a "8KiB bootloader" and USB communication.

# The "make flash" command does not work on the SKR mini E3. Instead,
# after running "make", copy the generated "out/klipper.bin" file to a
# file named "firmware.bin" on an SD card and then restart the SKR
# mini E3 with that SD card.

# See docs/Config_Reference.md for a description of parameters.
[gcode_macro CALIBRATE_NOZZLE_OFFSET]
description: Move to center of bed and calibrate nozzle offset
gcode:
  G90
  G0 X100 Y155 F1500
  PROBE_CALIBRATE

[gcode_macro LEVEL_BED]
description: "Level the bed manually."
gcode:
  BED_SCREWS_ADJUST

[gcode_macro CHECK_DEVIATION]
description: "Check the deviation of the bed from the last loaded mesh."
gcode:
  SCREWS_TILT_CALCULATE MAX_DEVIATION=0.05

[gcode_macro LIZ_IS_A_BAKA]
description: "Liz is a baka, so here's her start G-Code >.<"
gcode:
  BED_MESH_CALIBRATE
  BED_MESH_PROFILE SAVE=default

[gcode_macro _START_GCODE]
description: "The gcode that should be called from your slicer at the beginning of a print."
gcode:
  # Ender 3 Custom Start G-code
  G90
  G1 X2 Y30 Z30 F1500
  G1 Z0.28 F240
  G92 E0
  G1 Y220 E10 F1500 ; prime the nozzle
  G1 X2.3 F5000
  G92 E0
  G1 Y30 E10 F1200 ; prime the nozzle
  G92 E0
  G1 Z5 F1500 ; don't scratch the build plate

[gcode_macro _END_GCODE]
description: "The gcode that should be called from your slicer at the end of a print."
gcode:
  G91 # Relative positioning
  G1 E-2 F2700 # Retract a bit
  G1 E-2 Z0.2 F2400 # Retract and raise Z
  G1 X5 Y5 F3000 # Wipe out
  G1 Z10 # Raise Z more
  G90 # Absolute positioning

  G1 X0 Y220 # Present print
  M106 S0 # Turn-off fan
  M104 S0 # Turn-off hotend
  M140 S0 # Turn-off bed

  M84 X Y E # Disable all steppers but Z


[stepper_x]
step_pin: PB13
dir_pin: !PB12
enable_pin: !PB14
microsteps: 16
rotation_distance: 40
endstop_pin: ^PC0
position_endstop: 0
position_max: 235
homing_speed: 50

[tmc2209 stepper_x]
uart_pin: PC11
tx_pin: PC10
uart_address: 0
run_current: 0.580
stealthchop_threshold: 999999

[stepper_y]
step_pin: PB10
dir_pin: !PB2
enable_pin: !PB11
microsteps: 16
rotation_distance: 40
endstop_pin: ^PC1
position_endstop: 0
position_max: 235
homing_speed: 50

[tmc2209 stepper_y]
uart_pin: PC11
tx_pin: PC10
uart_address: 2
run_current: 0.580
stealthchop_threshold: 999999

[stepper_z]
step_pin: PB0
dir_pin: PC5
enable_pin: !PB1
microsteps: 16
rotation_distance: 8
endstop_pin: ^PC2
position_endstop: 0.0
position_max: 250

[tmc2209 stepper_z]
uart_pin: PC11
tx_pin: PC10
uart_address: 1
run_current: 0.580
stealthchop_threshold: 999999

[bltouch]
sensor_pin: PC14
control_pin: PA1
x_offset: -44
y_offset: 8
probe_with_touch_mode: True
# pin_up_touch_mode_reports_triggered = False
# z_offset: 3.0

[bed_mesh]
speed: 120
horizontal_move_z: 7
mesh_min: 30, 40
mesh_max: 250, 230
probe_count: 5
mesh_pps: 3
algorithm: bicubic

[safe_z_home]
home_xy_position: 140, 140
speed: 50
z_hop: 10
z_hop_speed: 5

[extruder]
step_pin: PB3
dir_pin: !PB4
enable_pin: !PD1
microsteps: 16
rotation_distance: 7.9797
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC8
# sensor_type: EPCOS 100K B57560G104F # Stock board config
sensor_type: NTC 100K MGB18-104F39050L32
sensor_pin: PA0
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 300

[tmc2209 extruder]
uart_pin: PC11
tx_pin: PC10
uart_address: 3
run_current: 0.650
stealthchop_threshold: 999999

[heater_bed]
heater_pin: PC9
# sensor_type: ATC Semitec 104GT-2 # Stock board config
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 54.027
pid_Ki: 0.770
pid_Kd: 948.182
min_temp: 0
max_temp: 130

[heater_fan heatbreak_cooling_fan]
pin: PC6
fan_speed: 1.0
heater: extruder
heater_temp: 50.0

[fan cooling]
pin: PC7 # Part cooling

# [heater_fan controller_fan]
# pin: PB15

# [fan]
# pin: PC6

[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100

[board_pins]
aliases:
    # EXP1 header
    EXP1_1=PB5,  EXP1_3=PA9,   EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
    EXP1_2=PA15, EXP1_4=<RST>, EXP1_6=PB9,  EXP1_8=PD6, EXP1_10=<5V>

# See the sample-lcd.cfg file for definitions of common LCD displays.
[include mainsail.cfg]