65 lines
4.5 KiB
Markdown
Executable File
65 lines
4.5 KiB
Markdown
Executable File
ins3DUltiSD.txt - June 13, 2022 version To print from an SD memory card:
|
|
U.1 Sometimes glue (glue stick (PVA)) should be put on the bed; it is
|
|
currently unclear when glue should be used U.2 Make sure there is
|
|
sufficient correct filament on the spool U.3 Turn on UltiMaker (power
|
|
switch is in back on left) U.4 Insert SD card (SD card must be left in
|
|
until print is finished) U.5 Select PRINT by turning dial U.6 Press dial
|
|
U.7 Select desired file by turning dial U.8 Press dial U.9 Wait for
|
|
printer to start and make sure it is printing properly
|
|
ins3DUltimaint.txt - Oct. 1, 2019 Leveling: L.1 Turn on power switch in
|
|
back if it is off L.2 Select MAINTENANCE by turning dial L.3 Press dial
|
|
L.4 Select BUILD-PLATE by turning dial L.5 Press dial L.6 Select
|
|
CONTINUE by turning dial L.7 Press dial L.8 Turn knob under front right
|
|
corner of bed below printhead until there is about a 1 mm gap between
|
|
the tip of the printhead and the bed L.9 Press dial L.10 Turn knob under
|
|
back center of bed below printhead until there is about a 1 mm gap
|
|
between printhead tip & bed L.11 Press dial L.12 Turn knob under front
|
|
left of bed below printhead until there is about a 1 mm gap between
|
|
printhead tip & bed L.13 Press dial L.14 Slide a sheet of paper between
|
|
printhead and bed (front right) then adjust knob until paper binds very
|
|
slightly L.15 Press dial L.16 Slide the paper between printhead & bed
|
|
(center back) and adjust knob until paper binds very slightly L.17 Press
|
|
dial L.18 Slide the paper between printhead & bed (front left) and
|
|
adjust knob until paper binds very slightly L.19 Press dial L.20 Slide
|
|
the paper between printhead & bed (front right) again and adjust knob if
|
|
needed so paper binds very slightly. L.21 Press dial (Instructions for
|
|
changing the filament have been deleted since they are outdated because
|
|
the extruder has been replaced) Calibrating the filament feed rate R.1
|
|
Connect the USB port on a tabletop computer to the port on the Ultimaker
|
|
with the appropriate cable R.2 Login: hacdc R.3 At Password: enter
|
|
standard password R.4 If the MATE Terminal icon is on the screen double
|
|
click on it and skip R.5-R.7 R.5 Click on Applications (top left) R.6
|
|
Select System Tools R.7 Click on MATE Terminal R.8 pronterface R.9 Click
|
|
on downward arrowhead under & just to right of help (at top) R.10 Click
|
|
on 250000 (connection speed) R.11 Click on Connect R.12 Heat: 185 R.13
|
|
If the nozzle is close to the bed or a print: move z 20 R.14 Wait for
|
|
the nozzle to heat to around 185 C R.15 Mark the filament at a known
|
|
distance from where it enters the feed mechanism (i.e., 120 mm) R.16
|
|
Extrude - At Length: enter a distance somewhat smaller than the mark
|
|
(i.e., 100 mm) R.17 Click on Extrude R.18 Wait until the Ultimaker
|
|
finishes extruding R.19 If the mark has entered the feed mechanism
|
|
repeat steps R.15-R.19 with a longer distance to the mark R.20 Measure
|
|
the distance from the mark to where the filament enters the feed
|
|
mechanism (i.e., 22.4 mm) R.21 Repeat R.15-R.20 using the same distance
|
|
to the mark & Length:; if the result is the same skip R.22-R.24 R.22
|
|
Follow the instructions at If the filament is not feeding properly: in
|
|
ins3DUltiprob.txt R.23 Repeat R.15-R.20 R.24 Repeat R.15-R.20 again with
|
|
the same distance to the mark & Length:; if the result is not the same
|
|
STOP and get expert help R.25 Subtract the distance to the mark from the
|
|
oringinal distance to determine how much filament was actually extruded
|
|
(i.e., 120-22,4 = 97.6 mm) R.26 At bottom right left of Send: M503 R.27
|
|
Click Send R.29 Find the line that starts echo: M92 & note the number
|
|
after E at the end of this line (i.e., 2158.32) R.29 Multiply this
|
|
number by the value of Length: (i.e., 2158.32 x 100 = 215832) R.30
|
|
Divide the result by the actual length of filament used (i.e., 215832 /
|
|
97.6 = 2211.39); this is the new value for E R.31 M92 E# where \# is the
|
|
new value (i.e., M92 E2211.39) R.32 Click Send R.33 M503 R.34 Click Send
|
|
R.35 Verify that E has the new value (i.e., E2211.39) R.36 Repeat
|
|
R.15-R.20 with a longer length (i.e., mark at 205 & extrude 200) R.37
|
|
Subtract the distance to the mark from the original distance to the mark
|
|
to determine how much filament was extruded R.38 If the actual length is
|
|
correct skip R.39; if it is way off STOP & get expert help (if help is
|
|
not available set Heat: to off or turn off Ultimaker) R.39 Repeat
|
|
R.26-R.35 R.40 M500 R.41 Click Send; the screen should state that the
|
|
new value was stored in EEPROM R.42 Heat: Click on Off
|
|
ins3DUltimaint.txt - May 8, 2018 |