62 lines
2.7 KiB
Markdown
Executable File
62 lines
2.7 KiB
Markdown
Executable File
**When you use the Cube, please add notes here. Newest at top.**
|
|
|
|
- Operational at Makersmiths. Seems to print a RasPi case fine.
|
|
[Mirage335](User:Mirage335 "wikilink")
|
|
([talk](User_talk:Mirage335 "wikilink")) 11:27, 8 April 2016 (PDT)
|
|
|
|
<!-- -->
|
|
|
|
- Printed Reprap Wilson Z Brace. Failed becuase cartridge ran out of
|
|
filament. Refilled filament making sure not to wind it too tightly
|
|
(Did by hand). Also made sure to release tension on wound filament
|
|
very few winds by counter rotation cartridge.
|
|
--[Nostromo](User:Nostromo "wikilink")
|
|
([talk](User_talk:Nostromo "wikilink")) 16:45, 16 April 2015 (PDT)
|
|
|
|
<!-- -->
|
|
|
|
- James reports: Attempted to print LCD Knob for Reprap Wilson but
|
|
printer refused to start printing with a "Cartridge Empty" error
|
|
message. Need to procure another cartridge and being doing cartridge
|
|
swap procedure to bypass this check.
|
|
--[Nostromo](User:Nostromo "wikilink")
|
|
([talk](User_talk:Nostromo "wikilink")) 09:52, 13 March 2015 (PDT)
|
|
|
|
<!-- -->
|
|
|
|
- James reports: Printed Y bearing holders from Prusa Mendel upgrade.
|
|
New mirrored build surface is working well with Elmers glue stick
|
|
(Easier to release parts). Several failed attempts at printing
|
|
filament bypass for cube because of poor STL file orientation.
|
|
--[Nostromo](User:Nostromo "wikilink")
|
|
([talk](User_talk:Nostromo "wikilink")) 09:34, 1 March 2015 (PST)
|
|
|
|
<!-- -->
|
|
|
|
- James reports: Printer is operating well. There is slight warping of
|
|
larger 4 inch parts on the corners but prints complete successfully.
|
|
The part I was printing failed in a strange way (printed part was
|
|
missing a geometric section). This might be due to forgetting to run
|
|
heal in the software. Also when transferring the .cube file to the
|
|
printer just use the USB key as it is far more reliable than the wifi.
|
|
--[Nostromo](User:Nostromo "wikilink")
|
|
([talk](User_talk:Nostromo "wikilink")) 13:49, 11 February 2015 (PST)
|
|
|
|
<!-- -->
|
|
|
|
- James reports: Performed Bed Leveling procedure (Ugh!!). Printing
|
|
Wilson Piecemeal Y Idler. The print looks a little smooshed on the
|
|
bottom. Consider recalibrating Z a little higher.
|
|
--[Nostromo](User:Nostromo "wikilink")
|
|
([talk](User_talk:Nostromo "wikilink")) 17:36, 5 February 2015 (PST)
|
|
|
|
<!-- -->
|
|
|
|
- James reports: Printed 2nd part on this printer. Reset Z axis to 1.60z
|
|
so that it wouldn't smoosh the part as much. seemes to have worked but
|
|
has a little bit of warping of the edges of the 5" part I was
|
|
printing. Removing the part is requiring long times in a water bath to
|
|
permeate the glue underneath --[Nostromo](User:Nostromo "wikilink")
|
|
([talk](User_talk:Nostromo "wikilink")) 16:01, 8 February 2015 (PST)
|
|
|
|
[Category:Cube](Category:Cube "wikilink") |