* Music player: cli tool and new worker
* Music player cli: flush message
* Music player: fix note calculation
* MusicPlayer: fix # parsing and add magic
* FuriHal: improve speaker volume handling. MusicPlayer: minor sustain improvements
* MusicPlayer: fix buffer overseek
* FuriHal: drop unused variables
* MusicPlayer: LFO 4 magic
* MusicPlayer: add RTTTL parser
* MusicPlayer: refactoring and add file open dialog on start
* MusicPlayer: fix memcpy issue and more
* FuriHal: force disconnect USB on early init and then leave usb line alone for some time.
* FuriHal: switch speaker to old volume. MusicPlayer: fix incorrect note history, and drop lfo from worker.
Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com>
* Disable USART in sleep
* Restore UART state on suspend/resume
* FuriHal: Enable stop mode and add insomnia to I2C and SPI
* Remove IDLE interrupt
* FuriHal: add FPU isr and disable all FPU interrupt, add core2 stop mode configuration on deep sleep
* FuriHal: tie stop mode debug with debug rtc flag
* FuriHal: adjust flash latency on clock switch, tie mcu debug with RTC debug flag
* FuriHal: move resource init to early stage
* Add EXTI pending check, enable debug traps with compile-time flag
* Wrap sleep debug functions in conditional compilation
* Remove erroneous changed
* Do not use CSS, remove it from everywhere
* Enable/disable USB on VBUS connect (prototype)
* FuriHal: add LPMS and DEEPSLEEP magic, workaround state inconsistency between cores
* FuriHal: honor c1 LMPS
* USB mode switch fix
* Applications: add flags and insomnia bypass system
* Correct spelling
* FuriHal: cleanup insomnia usage, reset sleep flags on wakeup, add shutdown api
* FuriHal: extra check on reinit request
* FuriHal: rename gpio_display_rst pin to gpio_display_rst_n
* FuriHal: add debug HAL
* FuriHal: add some magic to core2 reload procedure, fix issue with crash on ble keyboard exit
* FuriHal: cleanup ble glue, add BLE_GLUE_DEBUG flag
* FuriHal: ble reinit API, move os timer to LPTIM1 for deep sleep capability, shutdown that works
* FuriHal: take insomnia while shutdown
* Remove USB switch on/off on VBUS change
* Better tick skew handling
* Improve tick consistency under load
* Add USB_HP dummy IRQ handler
* Move interrupt check closer to sleep
* Clean up includes
* Re-enable Insomnia globally
* FuriHal: enable CSS
* FuriHal: remove questionable core2 clock shenanigans
* FuriHal: use core1 RCC registers in idle timer config
* FuriHal: return back CSS handlers, add lptim isr dispatching
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
Co-authored-by: nminaylov <nm29719@gmail.com>
* CLI: session refactoring
* Added forgotten define
* Desktop lock state save
* Dolphin: use proper type for value returned by dolphin_state_xp_to_levelup
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* C2OTA: wip
* Update Cube to 1.13.3
* Fixed prio
* Functional Core2 updater
* Removed hardware CRC usage; code cleanup & linter fixes
* Moved hardcoded stack params to copro.mk
* Fixing CI bundling of core2 fw
* Removed last traces of hardcoded radio stack
* OB processing draft
* Python scripts cleanup
* Support for comments in ob data
* Sacrificed SD card icon in favor of faster update. Waiting for Storage fix
* Additional handling for OB mismatched values
* Description for new furi_hal apis; spelling fixes
* Rework of OB write, WIP
* Properly restarting OB verification loop
* Split update_task_workers.c
* Checking OBs after enabling post-update mode
* Moved OB verification before flashing
* Removed ob.data for custom stacks
* Fixed progress calculation for OB
* Removed unnecessary OB mask cast
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* Use SysTick as OS tick timer
* Use LPTIM2 as tickless idle timer
* Remove dummy LPTIM2 IRQ handler
* Clean up clock init code
* Rename os timer to idle timer
* Advance hal ticks along with FreeRTOS's
* Improve SysTick control during tickless idle
* Improve idle timer precision
* Correct SysTick IRQ priority
* Main, FuriHal: move system startup to separate thread
* Minor code cleanup
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* Assets: recompile
* Makefile: add debug_other to main makefile
* Github: stop compilation if compiled assets not in sync with assets sources
* Assets: recompile
* Makefile: correct debug_other rule. Bt: prevent on system start hook from waiting for bt service
* Power, FuriHal: gauge self check report
* Loader: move on system start hook call to the beginning
* Add Auto Lock Time setting
* Update .gitignore
* Add value_index toolbox module
* Auto locking basic implementation
* Better AutoLock implementation, edge cases and cleanup
* Fix NULL pointer crash
* Turn off backlight shortly in locked mode
* Re-enable auto lock after pin lock
* Correctly handle start when pin locked
* Use timer to hide locked hint
* Use a single state variable instead of multiple bools
* Do not call update callback recursively
* Allow input when the Unlocked hint is shown
* Add a delay to backlight switch off while locking
* Better user input handling
* Switch backlight off after pin timeout
* Correct grammar in notification settings
Co-authored-by: あく <alleteam@gmail.com>
* WIP on stripping fw
* Compact FW build - use RAM_EXEC=1 COMPACT=1 DEBUG=0
* Fixed uninitialized storage struct; small fixes to compact fw
* Flasher srv w/mocked flash ops
* Fixed typos & accomodated FFF changes
* Alternative fw startup branch
* Working load & jmp to RAM fw
* +manifest processing for stage loader; + crc verification for stage payload
* Fixed questionable code & potential leaks
* Lowered screen update rate; added radio stack update stubs; working dfu write
* Console EP with manifest & stage validation
* Added microtar lib; minor ui fixes for updater
* Removed microtar
* Removed mtar #2
* Added a better version of microtar
* TAR archive api; LFS backup & restore core
* Recursive backup/restore
* LFS worker thread
* Added system apps to loader - not visible in UI; full update process with restarts
* Typo fix
* Dropped BL & f6; tooling for updater WIP
* Minor py fixes
* Minor fixes to make it build after merge
* Ported flash workaround from BL + fixed visuals
* Minor cleanup
* Chmod + loader app search fix
* Python linter fix
* Removed usb stuff & float read support for staged loader == -10% of binary size
* Added backup/restore & update pb requests
* Added stub impl to RPC for backup/restore/update commands
* Reworked TAR to use borrowed Storage api; slightly reduced build size by removing `static string`; hidden update-related RPC behind defines
* Moved backup&restore to storage
* Fixed new message types
* Backup/restore/update RPC impl
* Moved furi_hal_crc to LL; minor fixes
* CRC HAL rework to LL
* Purging STM HAL
* Brought back minimal DFU boot mode (no gui); additional crc state checks
* Added splash screen, BROKEN usb function
* Clock init rework WIP
* Stripped graphics from DFU mode
* Temp fix for unused static fun
* WIP update picker - broken!
* Fixed UI
* Bumping version
* Fixed RTC setup
* Backup to update folder instead of ext root
* Removed unused scenes & more usb remnants from staged loader
* CI updates
* Fixed update bundle name
* Temporary restored USB handler
* Attempt to prevent .text corruption
* Comments on how I spent this Saturday
* Added update file icon
* Documentation updates
* Moved common code to lib folder
* Storage: more unit tests
* Storage: blocking dir open, differentiate file and dir when freed.
* Major refactoring; added input processing to updater to allow retrying on failures (not very useful prob). Added API for extraction of thread return value
* Removed re-init check for manifest
* Changed low-level path manipulation to toolbox/path.h; makefile cleanup; tiny fix in lint.py
* Increased update worker stack size
* Text fixes in backup CLI
* Displaying number of update stages to run; removed timeout in handling errors
* Bumping version
* Added thread cleanup for spawner thread
* Updated build targets to exclude firmware bundle from 'ALL'
* Fixed makefile for update_package; skipping VCP init for update mode (ugly)
* Switched github build from ALL to update_package
* Added +x for dist_update.sh
* Cli: add total heap size to "free" command
* Moved (RAM) suffix to build version instead of git commit no.
* DFU comment
* Some fixes suggested by clang-tidy
* Fixed recursive PREFIX macro
* Makefile: gather all new rules in updater namespace. FuriHal: rename bootloader to boot, isr safe delays
* Github: correct build target name in firmware build
* FuriHal: move target switch to boot
* Makefile: fix firmware flash
* Furi, FuriHal: move kernel start to furi, early init
* Drop bootloader related stuff
* Drop cube. Drop bootloader linker script.
* Renamed update_hl, moved constants to #defines
* Moved update-related boot mode to separate bitfield
* Reworked updater cli to single entry point; fixed crash on tar cleanup
* Added Python replacement for dist shell scripts
* Linter fixes for dist.py +x
* Fixes for environment suffix
* Dropped bash scripts
* Added dirty build flag to version structure & interfaces
* Version string escapes
* Fixed flag logic in dist.py; added support for App instances being imported and not terminating the whole program
* Fixed fw address in ReadMe.md
* Rpc: fix crash on double screen start
* Return back original boot behavior and fix jump to system bootloader
* Cleanup code, add error sequence for RTC
* Update firmware readme
* FuriHal: drop boot, restructure RTC registers usage and add header register check
* Furi goes first
* Toolchain: add ccache support
* Renamed update bundle dir
Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com>
Co-authored-by: あく <alleteam@gmail.com>
* Power info command, validator fixes
* strdup in validator, fix memory leak
* furi_hal_crypto fixed again
* FuriHal: limit ARR and CC in speaker hal
* FuriHal: LL_TIM_DisableAllOutputs in speaker stop
* Rpc: fix memory leak in screen streaming
* Get rid of crypto_enable/crypto_disable
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* gpio, hsem, crypto: switch from HAL to LL/registers
* Moved GPIO initialization to furi_hal
* More HAL removed
* All HAL modules disabled
* HAL is finally removed
* hal_gpio -> furi_hal_gpio, main.h removed
* Bootloader build fix
* RTOS config moved to freertos-glue
* delay -> furi_hal_delay
Co-authored-by: あく <alleteam@gmail.com>
* FuriHal: refactor interrupts subsystem
* Furi,FuriHal: gather all ISRs under interrupt API, improve crtitical section and cleanup garbage
* FuriHal: mirgate ipcc and hsem to LL
* Format Sources
* FuriHal,BleGlue: move to new critical section
* Format Sources
* FuriHal: correct flash locking
* FuriHal: replace critical section with interrupt disable in OS routine, minor fixex
* iButton HAL: correct init and emulation sequence
* FuriHal: cleanup init/deinit routines for emulation timer
* FuriHal: cleanup TIM initialization routines in RFID and SubGhz
* iButton: delay in emulate loop
* Desktop: fix crash caused by invalid animation manager state, described in FL-2384
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* FuriHal: replace HAL with LL for ARR and CC
* Rfid, FuriHal: migrate emulation to LL
* RFID hal: disable arr preload during emulation
* Rfid, Furi, FuriHal: last piece of LL puzzle
* Rfid, Furi, FuriHal: filing the last piece of LL puzzle
Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com>
* usb mode switch lock
* lock_mutex removed
* Wait for session termination in rpc_cli, lock badusb and u2f if rpc session is opened
Co-authored-by: あく <alleteam@gmail.com>
* FuriHal: new speaker HAL
* FuriHal: drop PWM
* FuriHal: move COMP1 to LL
* FuriHal: move COMP1 to LL backport to F6
* FuriHal: remove missing gpio_rfid_carrier from F6
* FurHal: use LL for system controls in flash HAL
* Drop F6 source tree
* Drop F6 from GitHub workflow
* Tie USE_FULL_ASSERT with APP_UNIT_TESTS
* Speaker: return to old volume calculation
* FreeRTOS: move TCB header to glue
Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com>
* Streams: string stream
* String stream: updated insert/delete api
* Streams: generic stream interface and string stream implementation
* Streams: helpers for insert and delete_and_insert
* FFF: now compatible with streams
* MinUnit: introduced tests with arguments
* FFF: stream access violation
* Streams: copy data between streams
* Streams: file stream
* FFF: documentation
* FFStream: documentation
* FFF: alloc as file
* MinUnit: support for nested tests
* Streams: changed delete_and_insert, now it returns success flag. Added ability dump stream inner parameters and data to cout.
* FFF: simplified file open function
* Streams: unit tests
* FFF: tests
* Streams: declare cache_size constant as define, to allow variable modified arrays
* FFF: lib moved to a separate folder
* iButton: new FFF
* RFID: new FFF
* Animations: new FFF
* IR: new FFF
* NFC: new FFF
* Flipper file format: delete lib
* U2F: new FFF
* Subghz: new FFF and streams
* Streams: read line
* Streams: split
* FuriCore: implement memset with extra asserts
* FuriCore: implement extra heap asserts without inventing memset
* Scene manager: protected access to the scene id stack with a size check
* NFC worker: dirty fix for issue where hal_nfc was busy on app start
* Furi: update allocator to erase memory on allocation. Replace furi_alloc with malloc.
* FuriCore: cleanup memmgr code.
* Furi HAL: furi_hal_init is split into critical and non-critical parts. The critical part is currently clock and console.
* Memmgr: added ability to track allocations and deallocations through console.
* FFStream: some speedup
* Streams, FF: minor fixes
* Tests: restore
* File stream: a slightly more thread-safe version of file_stream_delete_and_insert
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* usb service, removed power observer
* fix usb restart after disable
* remove usb service from apps
* Applcations: remove dead extern
* New thread naming scheme for drivers
* New thread symbol naming scheme for drivers
Co-authored-by: あく <alleteam@gmail.com>
* Power: wait a little bit till message displayed on screen when executing power off. FuriCore: do not use bkpt in release builds(causing HardFault when SPI is active).
* Cleanup BSS section: add more consty consts to be more constish.
* Desktop: properly handle autostarted applications.
* Power, USB, LED driver improvements
* u2f hid descriptor fix
* variable_item_list: value alignment fix
* InputTypeRepeat handling in menu/submenu/var_item_list
* lp5562: fix bugs on 400khz i2c
* Scripts: lint in parallel.
* FuriHal: rename some USB structure to match naming convention. Drivers: update magic values in LP5562.
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* Makefile, Scripts: new linter
* About: remove ID from IC
* Firmware: remove double define for DIVC/DIVR
* Scripts: check folder names too. Docker: replace syntax check with make lint.
* Reformat Sources and Migrate to new file naming convention
* Docker: symlink clang-format-12 to clang-format
* Add coding style guide
* Furi, FuriHal, Desktop: much better crash handling. So wow.
* FuriHal: add missing include in FreeRTOSConfig.h
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* [FL-2162] SubGhz: Cli refactoring
* SubGhz: power reduction for Australia
* SubGhz: add frequencies for testing the Japanese region
* Desktop: fix fav app
Co-authored-by: Anna Prosvetova <anna@prosvetova.me>
Co-authored-by: あく <alleteam@gmail.com>
* U2F implementation prototype
* U2F data encryption and store, user confirmation request
* remove debug prints
* fix notification bug in chrome
* split u2f_alloc into u2f_init and u2f_alloc
* typo fix, furi-hal-trng -> furi-hal-random
* rand/srand redefinition
* SubGhz: a little bit of Dante.
* u2f_data naming fix
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* Libs: add FreeRTOS submodule. FuriHal: replace ST provided FreeRTOS with original one. FuriHal: for cmsis os hal and patch it for better compatibility with stream buffer.
* Makefile: fix svd plugin on blackmagic
* Lib: update STM32CubeWB package. Project: update project to match new cube package.
* Lib: properly rebase and upload STM32CubeWB
* BleGlue: switch ack logging level to trace
* Fixed the "ibutton can only emulate after reading" bug
* Fixed previous fix. FIXES FOR THE FIX GOD! BUGS FOR THE BUG THRONE!
* Fixed "Repeat code" position on code input screen
* Changed CAME protocol icon
* Brewfile: add imagemagick missing assets compiler dependency
* Correct fix for "Repeat code" position on code input screen
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* Incease mtu & buffer size
* bt: process mtu size in RPC callbacks
Co-authored-by: Tony Freeman <tonyfreeman@users.noreply.github.com>
Co-authored-by: gornekich <n.gorbadey@gmail.com>
* ReadMe: update flashing scripts section
* Furi: add record exists method to record store.
* FuriHal: early OS init and i2c timeouts based on os ticks.
* Storage: replace malloc with furi_alloc, fix errors found by pvs.
* iButton: properly handle shutdown in cli search command
* SubGhz: proper argument type in sscanf and incorrect position of logging in switch.
* SubGhz: add worker subghz_txrx
* SubGhz: added support for transferring Russian characters and support for backspace in CLI subghz_txrx
* SubGhz: refactoring subghz_txrx_worker, added a callback for accepting data in an empty one RX buffer
* SubGhz: fix conflict
* SubGhz: fix syntax errors
* Cli: document string_move usage and its behavior
* FuriHal: update subghz api and documentation. Subghz: move chat to subghz cli subcommand.
* Subghz: update text in chat cli
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* FuriHal: SPI refactoring, flexible bus reconfigration on fly, same desiag as i2c.
* Lib: update CC1101 driver documentation
* FuriHal: update spi symbol names to match naming convention.
* Project: fix release build, replace asserts with checks.
* FuriHal: i2c refactoring, new bus access model, flexible bus gpio configuration.
* FuriHal: set i2c pins to high on detach.
* FuriHal: more i2c bus events, put bus under reset when not used, move bus enable/disable routine to bus handler.
* FuriHal: fix i2c deadlock in power api, add external i2c handle.
* [FL-2051] BadUsb: new GUI
* add missing assets
* skip empty lines and leading spaces
* SubGhz: add alignment check to keystore mess with iv routine
Co-authored-by: あく <alleteam@gmail.com>
* SubGhz: GUI RAW Read view
* SubGhz: GUI Read RAW refactoring
* SubGhz: fix bug wrong frequency of the allowed transmission
* GUI Read RAW refactoring
* SubGhz: fix set the default frequency
* SubGhz: fix save filename when returning from another menu
* SubGhz: fix Send and Back button behavior
Co-authored-by: あく <alleteam@gmail.com>
* USB-UART: new gui
* Furi: use furi_console for logging instead of printf.
* CDC: calling open/close callbacks on interface change
* fix vcp_tx block on disconnect
* USB mode set by struct pointer
* FuriHal: proper event sequence on vcp reconnect
* disable debug prints
* HAL: add context to UART IRQ's
* Context usage in UART IRQ and CDC callbacks
* USB-UART: geting rid of baudrate limitations
* FuriHal: remove struct pollutant in usb api.
Co-authored-by: あく <alleteam@gmail.com>
Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com>
* [FL-2010] furi-hal-vcp rework
* Fix connect state change on vcp enable
* New thread naming scheme and stack size adjustment.
* Applications: rename worker threads to match new naming scheme.
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* Toolbox: fix null pointer dereference in manchester decoder.
* FuriHal: use MPU to protect from null pointer dereference, replace flash driver with our own implementation.
* rpc: increase RPC buffer size. Add get available buffer size API
* bt: add flow control characteristic to serial service
* ble: change updating flow control characteristic logic
* rpc: add buffer is empty callback
* bt: add notification about empty RPC buffer
* ble: add more debug info
* serial_service: add mutex guarding available buffer size
* ble: remove debug logs in serial service
* Core: wipe memory after free. RFID,iButton: fix iterator use after invalidation.
* Debug: support unix wildcards for register matching in svd, update MCU description file and minify it.
* Toolbox: getter for File in FlipperFile.
* Makefile: conditional flashing
* SubGhz: keeloq_mfcodes encryption tool.
* FuriHal: proper IV handling on CBC in crypto. SubGhz: add support for encrypted keeloq keys. Makefile: move formatting to top Makefile.
* SubGhz: rename some function names to match naming scheme.
* SubGhz: encryption tool, fix windows line endings
Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com>
- RPC: added CLI command to start session - all input bytes goes into RPC, all RPC output goes into VCP
- RPC: added command to close session (actually it only notifies transport layer)
- RPC: added recursive rmdir
- RPC: hard-coded listing for root directory (any, ext, int)
- Fixed CLI leak
- Fixed furi_record_delete leak
- Unit tests: repaired
- Unit tests: corrected output - remove excess, change dots with progress spinner
- Unit tests: added leak check
- Unit tests: SD mount check before start
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* File_Worker: getting the name of a new file with an index
* SubGhz: add decoder RAW protocol
* SubGhz: add view Save RAW
* SubGhz: refactoring subghz custom event
* SubGhz: fix syntax
* SubGhz: fix error build
* SubGhz: test build
* SubGhz: refactoring subghz, add rename, delete, start and emulate RAW signal
* SubGhz: fix triangle glitch in save raw view
* SubGhz: fix receiver config scene
* SubGhz: fix transfer after returning from save scene
* Canvas: add font rotation
* SubGhz: raw protocol encoder
* SubGhz: fix error completion of transfer raw encoder
* SubGhz: increased the speed of reading RAW data from a flash drive, displaying the name of the saved file in the Save RAW scene
* Canvas: fix font rotation
* SubGhz: fix navigation save RAW scene
* SubGhz: add decode came atomo
* Git: renormalize
* Cleanup sources and enums
* Gui: add font direction to canvas reset, canvas init sequence cleanup.
* SubGhz: reorder menu.
* Gui: correct canvas_set_font_direction signature
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* ble-glue: add on connect \ disconnect, on send \ received callbacks
* bt: rework service with furi-hal-bt and callbacks
* bt: update battery level on connect
* ble-glue: set one callback with parameters
* bt: rework callbacks, remove unused API
* ble-glue: remove dead code
* furi-hal-bt: add documentation
* ble-glue: apply changes for f7 target
* bt: rename RpcInstance -> Rpc
* ble: add disconnection reason
* ble: don't open bt record from GAP
* bt: fix RPC session close
* Assets: separate targets for icons and protobuf
Co-authored-by: あく <alleteam@gmail.com>
* ToolBox: add manchester-decoder and manchester-encoder
* SubGhz: add new FM config cc1101
* Subghz: add protocol Kia
* SubGhz: fix receiving the last packet Nero Radio
* SubGhz: app protocol CAME Twin (TW2EE/TW4EE)
* SubGhz: add protocol CAME Atomo (AT03EV/ AT04EV)
* F7: sync with F6
* SubGhz: add frequency analyzer
* SubGhz: remove space from file name
* SubGhz: frequency analyzer add filter and fix view
* [FL-1939] GubGhz: Frequency analyzer redesign
* SubGhz: fix incorrect subghz api call sequence in frequency analyzer worker
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* FuriHal: add charge suppress API.
* FuriHal: add guards to insomnia and charge suppress routines.
* FuriHal: proper API for scheduler in power.
* FuriHal: move charging control from critical section, fix deadlock.
* Gui: use FreeRTOS native timers controls for IconAnimation, fix crash on animation start stop
* [FL-1811] FuriHal: move core2 startup to hal init stage, prevent working with flash controller till core2 startup finish. #704
* SubGhz: fix GO0 low on last hop transmission, decreased DutyCycle in tests
* SubGhz: test_static fix max 5 sec in transmission mode, DutyCycle <23%
* [FL-1815] SubGhz: prohibiting transmission if it is not within the permitted range for the given region
* SubGhz: fix F7 furi-hal-subghz
* SubGhz: fix logic working tests
* SubGhz: fix princeton encoder for test
* SubGhz: add log princeton encoder
* [FL-1856] Subghz: fix output a double error if the file cannot be opened
* [FL-1851] SubGhz: add deleting Stored Signals in SubGHz App
* SubGhz: add rename file SubGhz app
* SubGhz: update stats message in princeton
* SubGhz: correct spelling
* SubGhz: fix FM config, add hardware signal processing less than 16 μs, add added filter for processing short signals
* SubGhz: add Scher-Khan MAGICAR Dinamic protocol
* SubGhz: sync fury targets
Co-authored-by: あく <alleteam@gmail.com>
* bt: add authentication for all characteristics
* bt: app_ble cleanup
* bt: add start and stop advertising API
* bt: rework application with start and stop advertising API
* bt: support f7 target
* bt: f7 target remove unused files
* bt: stop advertising in bt debug application
* bt: fix bt status bar update
* bt: change bluetooth On Off order
* WidGet: fix name Multiline String Element
* SubGhz: rename SubGhzProtocol to SubGhzParser and bring it up
* SubGhz: a new way to navigate in receiver views
* SubGhz: fix syntax
* WedGet: add forwarding input type to wedget button callback, fix using a callback in an application
* SubGhz: add assertions and status checks
* SubGhz: fix syntax
* [FL-1790] SubGhz: fix GateTX
* SubGhz: add 434.42 MHz frequency support
* SubGhz: rename type protocol, add decoder stage names
* SubGhz: fix navigation through received signals when changing scenes
* SubGhz: fix 2-fsk config
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* ble: remove heart rate profile
* ble-glue: delete dead code
* ble-glue: dis refactoring
* ble-glue: add battery service
* broken ble_common refactoring
* ble-glue: advertise 128 bit service uid
* ble-glue: remove dead code
* ble: advertise service 16 bit uid depending on flipper color
* ble-glue: remove debug
* ble: intriduce serial service
* ble: serial over ble
* bt: serial echo server
* bt: serial service process indicate acknowledge
* bt: serial service event handler update
* bt: refactore battery service
* bt: add battery level apdate API
* power: update battery level on change
* bt: refactore device information service
* app_ble: pairing configuration
* bt: display pin code
* bt: refactor battery service
* bt: refactor device info service
* bt: change advertise timer to freertos one
* bt: separate app_ble to hci and gap
* bt: increase max ble packet size
* gap: refactoring
* bt: refactor serial service
* bt: support f7 target
* bt: not blocking pin code show request
Co-authored-by: Anna Prosvetova <anna@prosvetova.me>
Co-authored-by: あく <alleteam@gmail.com>
* RFID: pull antenna down when emulating
* Rfid: fixed HID emulation by adding zero pulse every 4 bits
* Rfid: HID emulation fixed with DSP based FSK oscillator.
* Rfid: receive 125KHz clock for emulation timer from antenna and comparator
* Rfid: commented unused variable
* Firmware: rollback changes in f6.
* Add F7 target based on F6.
* F7/F6: update cube projects, apply changes to the targets, update linker scripts with correct RAM start values.
* FuriHal: RFID init routine.
* Scripts: update OTP tool for v11 board
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* ble: remove heart rate profile
* ble-glue: delete dead code
* ble-glue: dis refactoring
* ble-glue: add battery service
* broken ble_common refactoring
* ble-glue: advertise 128 bit service uid
* ble-glue: remove dead code
* ble: advertise service 16 bit uid depending on flipper color
* ble-glue: remove debug
* ble: intriduce serial service
* ble: serial over ble
* bt: serial echo server
* bt: serial service process indicate acknowledge
* bt: serial service event handler update
* bt: refactore battery service
* bt: add battery level apdate API
* power: update battery level on change
* bt: refactore device information service
Co-authored-by: あく <alleteam@gmail.com>
* Cli: add missing const in cli_write.
* Gui, Input: bit fields based key complementarity on all levels, key and type names API.
* Gui: minor cleanup of bit filed usage
* SubGhz: Fix Timer hopping
* SubGhz: add display of received packages and their maximum number. redesigned interface, the maximum number of received packages increased to 50
* SubGhz: add clearing history on exit read scene, jump after saving the key into the history of received signals
* SubGhz: Fix honoring the width of the icon for transmitter scene
* RFID: Fix [FL-1755] freeze after key emulation
* SubGhz: drop analyze scene and views
* SubGhz: fix save scene
* Input, GUI: new event delivery scheme that groups event for complementarity.
* Gui: update View Dispatcher documentation
* Gui: remove dead code, wait till all input events are delivered in ViewDispatcher in queue mode.
* Gui: update comment in ViewDispatcher
* FuriHal: fix incorrect clock disable invocation
* FuriHal: proper include
* SubGhz: properly reset history in receiver view
* Gui: correct view switch order and non-complementary events discarding
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* SubGhz: Add millis() furi, add subghz history struct
* SubGhz: Fix subghz history
* Gubghz: Fix code repeat history, add clean history
* SubGhz: reading and adding keys to history
* Gui: Renaming Sub 1-Ghz -> SubGhz
* Archive: Renaming Sub 1-Ghz -> SubGhz
* SubGhz: Add menu history, modified button for sending a signal, changed output of data about accepted protocol
* Archive: Fix name subghz
* SubGhz: Menu navigation
* Assets: Add assets/SubGHz/icon.png
* Assets: add new icons for subghz
* SubGhz: Fix name Add manually scene
* SubGhz: Fix load icon Read scene. rename encoder struct, rename protocol function load from file, add load raw data protocol, add info pleasant signals all protocol
* SubGhz: fix memory leak
* SubGhz: change of receiving frequency for read scene
* SubGhz: Add save/load frequency and preset, add automatic configuration of transmit/receive to the desired frequency and modulation, add button "save" config scene
* SubGhz: Fix frequency and preset, fix frequency add manualli scene, fix re-executing the parser
* Furi-hal-subghz: add 2-FSK config, fix ook config 650KHz BW Tx filter
* Fix formatting and release build
* SubGhz: Delete read scene
* SubGhz: Fix frequency add manualli scene, refactoring code
* SubGhz: 2 profiles for OOK, fix broken build.
* SubGhz: Add passing static codes from read scene, add notification read scene, refactoring code
* SubGhz: fix assert on worker double stop.
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* USB-CDC: accepting the next data packet only if we process previous data
* USB-CDC: use USB FS packet size
* HAL-console: puts method
* Check: print assertion data
* FuriHal: rx stream free space aware CDC confirmation.
* Bootloader: pull down USB lines, leave the rest to the firmware or bootloader
* F6: cleanup and move USB code to usb-glue folder, add USB suspend/resume events to VCP, cleanup target.mk, fix missing motd message in cli when using minicom.
* F5: cleanup the rest of USB glue code, adjust LPM and Power info data in descriptor.
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
- Restrict with 31 bytes length for remote and signal name
- Don't stuck for 0 PWM cycle timings
- Support timings > 65535 PWM cycles
- Fix remote file open error
- Add IRDA TX debug redirect
- Add remote parse error print, improve parsing, support tabs
- Fix stucks with uncorrect RAW signal values, long strings in remote file, etc
- Fix HAL signals capturing (save previous read value)
- Fix leak in case of failed parsing
* Storage-cli: the file write function is splitted into a function for working with text and function for raw data
* Storage-cli: read_chunks, renamed write_raw to write_chunk
* Storage-cli: fix typo
* SD Hal: fixed wrong read/write block address
* HAL-console: printf
* Storage benchmark: more popular sizes
* Toolbox: md5
* Storage-cli: better read_chunks function, md5 hash function
* Notification: fixed incorrect error message when loading settings
* Storage-cli: stat command
* Storage-cli: stat, "/" is also storage
* Scripts: add storage managment script
* Scripts, storage lib: send command with known response syntax instead of SOH
* Scripts: python3 from env
* Storage-cli: fixed mess with error texts
* Storage-cli: write, show welcome message only if we didn't have any errors
* Storage: poorly fixed folders copying
* Storage: close an old file if an error occurred while opening a new file
* Storage-cli: fixed storage info spacing
* Scripts: use positional arguments in storage.
* Scripts: explicit string encoding and decoding, documentation in comments.
Co-authored-by: あく <alleteam@gmail.com>
* FuriHal: update STM32CubeWB to latest version.
* Makefile: debug other script
* FuriHal: correctly handle 0 size transfers in VCP
* Dolphin: cleanup and minor timer tuning.
* FuriHal: update FreeRTOS config with bigger timer command queue.
* FuriHal: delayed irq enabling, fixes missing ticks.
* FuriHal: use SFSA to determine free space for internal FS, update linker script to use as much space as theoretically possible.
* Scripts: update core2 flashing scripts and OB data.
* Github: bundle resources, core2 firmware and supplementary data.
* GitHub: versioning for supplemental artifacts
* SubGhz: the functions of saving loading KeeLog have been modified, saving KeeLog is prohibited
* SubGhz: Fix displaying Nice FlorS in the Raed scene
* SubGhz: Fix displaying Faac SLH in the Raed scene
* SubGhz: Fix displaying iDo in the Raed scene
* SubGhz: Fix displaying Star Line in the Raed scene
* SubGhz: Fix displaying Nice Flo in the Raed scene, added save and load functions. (testing needed, no remote control)
* SubGhz: subghz_beginadded common encoder upload signal
* SubGhz: add Came encoder
* SubGhz: modified pricenton encoder, fix view transmitter hide the "Send" button if there is no encoder
* SubGhz: add nice flo encoder, need testing no remote control
* SubGhz: add gate_tx encoder
* SubGhz: add nero_sketch encoder
* SubGhz: add keelog encoder
* SubGhz: add long upload upload while the button is pressed while releasing the transfer is over, with a check for sticking (maximum 200 upload repetitions)
* SubGhz: fix max upload
* SubGhz: Fix structure subghz add encoder
* SubGhz: add generating and sending a dynamic keelog key, refactoring the code
* SubGhz: add notifications
* SubGhz: add creating a new remote control (Pricenton, Nice Flo 12bit, Nice Flo 24bit, CAME 12bit, CAME 24bit, Gate TX, DoorHan)
* SubGhz: Fix load file, fix scene start
* Subghz: Fix show key
* SubGhz: Fix subghz_cli
* SubGhz: Fix furi-hal-subghz
* Format sources
* SubGhz: standard notification scheme, fix broken assert in DMA.
* SubGhz: move level alignment logic to furi-hal-subghz, fix spelling, cleanup.
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
* FuriHal: port spi to ll. Bootloader: add spi and display.
* Makefile: rollback disabled freertos introspection
* FuriHal: spi lock asserts. F6: minor cleanup port sdcard shenanigans to furi_hal_gpio.
* SdCard: port missing bits to furi-hal-gpio
* FuriHal: fix broken RX in SPI, update SPI API usage. RFAL: more asserts in SPI platform code.
* GUI: clear canvas on start. FuriHal: no pullup on radio spi bus.
* FuriHal: use check instead of assert in spi lock routines
* FuriHal: remove timeouts
* SdHal: add guard time to SDCARD CS PIN control.
* FuriHal: proper name for SPI device reconfigure routine. SdHal: one more enterprise delay and better documentation.
* Bootloader: update DFU text and add image.
* FuriHal: drop unused ST HAL modules.
* SdHal: fixed swapped hal_gpio_init_ex arguments
* SpiHal: fixed swapped hal_gpio_init_ex arguments
* IrdaHal: use hal_gpio_init instead of hal_gpio_init_ex
* RfidHal: fixed swapped hal_gpio_init_ex arguments
Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com>
* Rfid: indala 40134 validation and decoding
* Rfid: show indala info
* Rfid: decoder to output comparator signal on gpio pins
* Rfid: working indala 40134 decoder
* HAL: added function to change rfid timer parameters on the fly
* RFID: Indala reading, card detection, card verification
* Rfid: indala writing
* Lib: add random name library
* Text_input: add default text clearing
* All: rework all applications with new text_input API
* Nfc: fix removing dev file on save_name scene enter
* Lib: move all free radicals to toolbox and update API usage.
Co-authored-by: あく <alleteam@gmail.com>
* FS-Api: removed datetime manipulation functions and most of the file flags
* Filesystem: common proxy api
* Filesystem: renamed to Storage. Work has begun on a glue layer. Added functions for reentrance.
* Storage: sd mount and sd file open
* Storage: sd file close
* Storage: temporary test app
* Storage: free filedata on close
* Storage: sd file read and write
* Storage: added internal storage (LittleFS)
* Storage: renamed internal commands
* Storage: seek, tell, truncate, size, sync, eof
* Storage: error descriptions
* Storage: directory management api (open, close, read, rewind)
* Storage: common management api (stat, fs_stat, remove, rename, mkdir)
* Dolphin app and Notifications app now use raw storage.
* Storage: storage statuses renamed. Implemented sd card icon.
* Storage: added raw sd-card api.
* Storage settings: work started
* Assets: use new icons approach
* Storage settings: working storage settings
* Storage: completely redesigned api, no longer sticking out FS_Api
* Storage: more simplified api, getting error_id from file is hidden from user, pointer to api is hidden inside file
* Storage: cli info and format commands
* Storage-cli: file list
* Storage: a simpler and more reliable api
* FatFS: slightly lighter and faster config. Also disabled reentrancy and file locking functions. They moved to a storage service.
* Storage-cli: accommodate to the new cli api.
* Storage: filesystem api is separated into internal and common api.
* Cli: added the ability to print the list of free heap blocks
* Storage: uses a list instead of an array to store the StorageFile. Rewrote api calls to use semaphores instead of thread flags.
* Storage settings: added the ability to benchmark the SD card.
* Gui module file select: uses new storage api
* Apps: removed deprecated sd_card_test application
* Args lib: support for enquoted arguments
* Dialogs: a new gui app for simple non-asynchronous apps
* Dialogs: view holder for easy single view work
* File worker: use new storage api
* IButton and lfrrfid apps: save keys to any storage
* Apps: fix ibutton and lfrfid stack, remove sd_card_test.
* SD filesystem: app removed
* File worker: fixed api pointer type
* Subghz: loading assets using the new storage api
* NFC: use the new storage api
* Dialogs: the better api for the message element
* Archive: use new storage api
* Irda: changed assest path, changed app path
* FileWorker: removed unused file_buf_cnt
* Storage: copying and renaming files now works between storages
* Storage cli: read, copy, remove, rename commands
* Archive: removed commented code
* Storage cli: write command
* Applications: add SRV_STORAGE and SRV_DIALOGS
* Internal-storage: removed
* Storage: improved api
* Storage app: changed api pointer from StorageApp to Storage
* Storage: better file_id handling
* Storage: more consistent errors
* Loader: support for NULL icons
* Storage: do nothing with the lfs file or directory if it is not open
* Storage: fix typo
* Storage: minor float usage cleanup, rename some symbols.
* Storage: compact doxygen comments.
Co-authored-by: あく <alleteam@gmail.com>
* ApiHal: console abstraction, change uart baud rate to 230400. Bootloader: drop F5. Furi: prevent thread local output to serial console in stdglue.
* ApiHal: take control over system initialization, reorder some subsystems in a hope of fixing USB issues.
* Main: cleanup dead code. ISR: take care of HSECSS by our self. USB: leave clock configuration alone.
* F6 cube: switch RCC to LL.
* Cli: rollback return behavior.
* Firmware: drop F5 target
* Rename app-loader to loader
* Update code owners file
* Loader: global application start lock API, minor refactoring
* Archive: update loader usage
* Cli: Command flags, global application start lock
* Apps: update cli API usage
* Bootloader: minor refactoring
* Firmware: minor build refactoring
* SubGhz: GUI packet test
* SubGhz: drop packet transmission and unused presets
* Github: drop F5 from build
* Archive: favorites
* Archive: a little bit more of Favorites
* Add RAW format
* F5 stubs for build to pass
* Fix saving decoded signal error
* Irda: set ISR before starting timer, remove explicit NVIC configuration
Co-authored-by: あく <alleteam@gmail.com>
* gui: refactore ViewNavigator -> SceneManager
* view_dispatcher: remove scene controller, add custom and navigation cb
* scene_manager: rework scene controller, move AppScene from lib
* nfc: rework nfc scenes with new scene controller API
* view_dispatcher: crash on free if not all views were freed
* nfc: introduce scene declaration
* scene_manager: allocate and configure application scenes
* nfc: rework nfc with new Scene Manager API
* scene_manager: remove dublicated scene handlers allocation
* nfc: rework nfc app with new scene manager API
* view_dispatcher: add tick event
* scene_manager: add tick event type and handler
* nfc: rework notifications with tick event
* scene_manager: remove scene id from scene structure
* scene_manager: rename array -> stack, add documentation
* api-hal-nfc: remove listen activation processing
* nfc_scene_start: shorter submenu call
* nfc: fix nfc file name
* nfc: fix Retry in mifare ul success read
* nfc_cli: fix read timeout in nfc_detect CLI command
Co-authored-by: あく <alleteam@gmail.com>
* SubGhz: changing the operation of the capture timer, and the logic of the work of parsers
* Add toolbox lib. Move levels to toolbox. Subghz switch to levels.
* Subghz: update worker signatures
* SubGhz: pluggable level duration implementations.
* SubGhz : test drawing pictures in Gui
* SubGhz: Added a callback with the parser structure as argument
* SubGhz: copy protocol data to model
* SubGhz: refactoing code
* SubGhz: cleanup and format sources
* SubGhz: remove comments
Co-authored-by: Aleksandr Kutuzov <alleteam@gmail.com>
Co-authored-by: DrZlo13 <who.just.the.doctor@gmail.com>
* Cli: merge version and hwinfo and form machine/human readable key value set.
* Backport F6 changes to F5. Add readme to cli_command_device_info rountine
* Cli: return proper order to radio stack version in device_info command
Co-authored-by: SG <who.just.the.doctor@gmail.com>
* ApiHal: set frequency and path in one go. Drivers: proper frequency registers calculation for CC1101. Update subghz cli to match new api.
* SubGhz: preparation for parsers porting, tim2 sharing
* ApiHal: add interrupts API, move all TIM2 related things there.
* SubGhz: refactor protocol lib and add keeloq.
* SubGhz: proper init_set for keeloq manafacture key
* SubGhz: port more protocols to lib
* SubGhz: load keeloq manufacture keys from sd card (if any).
* SubGhz: format output from protocols.
* SubGhz: use default frequency in subghz_rx cli command.
* SubGhz: keeloq key types
* Fix compillation error when internal storage disabled
* SubGhz: minor cleanup
* SubGhz: properly handle timeout and reset signal in subghz_rx
* SubGhz: Worker, Capture View. Furi: emulate thread join.
* SubGhz: free strings on keeloq key load end
* SubGhz: update protocols reporting API, app refactoring and capture view, update API HAL usage.
* SubGhz: update dump formatting
* ApiHal: backport subghz preset to F5
* ApiHal: backport subghz frequency range to F5
* Add saving to SD-Card (not ready yet)
* Add saving to SD-card (done)
* Select previous menu item
* Fix central button
* Fix current_button
* Refactoring
* Add notifications
* [FL-1417] Add IRDA CLI
CLI commands:
1) ir_rx
Receives all IR-trafic, decodes and prints result to stdout
2) ir_tx <protocol> <address> <command>
Transmits IR-signal. Address and command are hex-formatted
* Fix BUG with random memory corruption at random time in random place in random universe in random unknown space and time forever amen
* Fix submenu set_selected_item
* Bring protocol order back
* Add TODO sdcard check
* USB CDC descriptor: join product name from two strings
* add f5 support
* USB CDC descriptor: use constant device name across all device
* BLE: use device name in advertising and model
* BLE: truncate device name
Co-authored-by: あく <alleteam@gmail.com>
* api-hal-spi: make fast and slow sd card devices
* api-hal-spi: add configuration for spi bus
* fatfs: rework sd card driver with api-hal-spi
* api-hal-spi: enable spi in bus reset
* HAL interrupl manager: cleaned version
* HAL interrupt manager: mem barriers
* HAL interrupt manager: volatile interrupt list
Co-authored-by: あく <alleteam@gmail.com>
* Add more more frequencees and change ok key bahavior to toggle
* GUI: add queue support to ViewDispatcher
* SubGhz: basic cli
* SubGHz: pt send cli
* SubGhz: carrier cli commands.
* Fix irda test data merge artifacts
